Sinclair MV-D BI Series User Manual Download Page 14

   started up, press "TIMER ON" button to cancel it.

 TIMER OFF button

   "TIMER OFF" button can set the time for timer off. After pressing this button,"     "

   icon disappears and the word "OFF" on remote controller blinks. Press "+" or "-" 

   button to adjust TIMER OFF setting. After each pressing "+" or "-" button, TIMER 

   OFF setting will increase or decrease 1min. Hold "+" or "-" button, 2s later, the 

   time will change quickly until reaching your required time. 

   Press "TIMER OFF" word "OFF" will stop blinking. "     " icon resumes displaying. 

   Cancel TIMER OFF. Under the condition that TIMER OFF is started up, press

   "TIMER OFF" button to cancel it.

Note:

● Under on and o

ff status, you can set TIMER OFF or TIMER ON simultaneously.

● Before setting

 TIMER ON or TIMER OFF, please adjust the clock time.

 After starting up TIMER ON or TIMER OFF, set the constant circulating valid.   

   After that, air conditioner will be turned on or turned off according to setting time. 

   ON/OFF button has no effect on setting. If you don’t need this function, please

   use remote controller to cancel it.

X-FAN button

11

12

Press this button under cool and dry mode to start up x-fan function, and "     " icon 

on remote controller will be displayed. Press this button again to cancel x-fan 

function, and "     "icon will disappear.

Note:

● When x-fan function is on, if the air conditioner is turned of

f, indoor fan will still

   operate at low speed for a while to blow the residual water inside the air duct.

● During x-fan operation, press X-

FAN button to turn off x-fan function. Indoor fan 

   will stop operation immediately.

TEMP button

By pressing this button, you can see indoor set temperature, indoor ambient temp-

erature or outdoor ambient temperature on indoor unit’s display. The setting on

remote controlleris selected circularly as below:

no display

● When selecting "     " or no display with remote controlle

r, temperature indicator 

   on indoor unit displays set temperature.

● When selecting "     " with remote controlle

r, temperature indicator on indoor unit

   displays indoor ambient temperature.

7

Summary of Contents for MV-D BI Series





















Reviews: