manualshive.com logo in svg

Sinclair FC-D09AI, User Manaul

Share
Download
Sinclair FC-D09AI User Manaul Download Page 13

 DRY (Dehumidifying)  Mode Operations 

Connect  the  unit  to  power  supply.  Press  the  “ON/OFF” 
key. Press the “MODE” key to select “DRY (Dehumidifying)” 
mode. Use the “Temperature” key to adjust the set tempe-
rature for the room.

a)  After  the  unit  is  connected  to 
power supply, the air conditioning unit 
shall enter the operating status if you 
press the ON/OFF key

b) Press the mode key and select the 

(  ) mode

c) Press the temperature key and set 
the temperature as required

 Fan Mode Operation 

Connect the unit to power supply. Press the “ON/OFF”key. 
Press the “MODE” key to select “FAN” mode. The unit shall 
operate  under  “FAN”  mode.  Press  the  “FAN”  key  to  select 
from high, medium and low speed.

a)  After  the  unit  is  connected  to 
power supply, the air conditioning unit 
shall enter the operating status if you 
press the ON/OFF key

b) Press the mode key and select the 

(  )mode

１２

Summary of Contents for FC-D09AI



































Reviews:

No comments

Brands by name

Popular brands

Load more brands