manualshive.com logo in svg

Sinclair AST-24AI, Service Manual, Page: 54 / 68

Share
Download
Sinclair AST-24AI Service Manual Download Page 54

Service Manual

50

Installation and Maintenance

Procedure

Step

8.Remove upper cover, horizontal louver, swing board

9.Remove swing motor and air-guide motor

a.Remove screws used for fixing the air-
guide motor and the remove the air-guide 
motor.
b.Remove  screws  used  for  fixing  the 
motor cover, remove the motor cover and 
then remove the swing motor. 

a.Remove 2 screws at the upper part of 
the upper cover and two screws at the 
back side of the air-outlet panel.
b.After removing the air-guiding connecting 
robe, and then pull the horizontal louver 
outwards to remove it. 
c.After removing the air swing connection 
rod,  pull  the  swing  board  inwards  to 
remove it.

swing board

air-guide motor

motor cover

swing motor

air swing 

connecting rod

upper cover

horizontal  louver

air-guiding connecting rod

screw

screw

screw

10.Remove wind board

wind board

Remove 11 screws used for fixing the wind 
board and then remove the wind board.

Summary of Contents for AST-24AI





































































Reviews:

No comments