manualshive.com logo in svg

Sinclair ASDU-09A, User Manual

Share
Download
Sinclair ASDU-09A User Manual Download Page 10

Failure Display

When there is failure in the unit operation, “ERROR” will
flash on the LCD of the wire controller and the code of fai-
lure will also be displayed. When there are multiple failures
at the same time, the codes of failures will be displayed
one after one on the wire controller. The first digit of the
code denotes the system number. When there is only one
system, the system number is not displayed. The last two
digits denote the detailed failure code. For example, the
code in

 left

means low pressure protection of com-

pressor.

The Codes of Failure Definitions are as Follows:

Fault code

Fault

Fault code

Fault

E0

Pump Failure

F0

Failure of Indoor Room Sensor at Air Intake

E1

Compressor High Pressure
Protection

F1

Failure of Evaporator Temp. Sensor

E2

Indoor Frost-Proof Protection

F2

Failure of Condenser Temp. Sensor

E3

Compressor Low Pressure
Protection

F3

Failure of Outdoor Ambient Sensor

E4

Compressor Exhaust High 
Temperature Protection

F4

Failure of Exhaust Temp. Sensor

E5

Compressor Overheat 
 

 

F5

Failure of Indoor Room Sensor at Wire
Controller

E6

Communications Failure

E8

Indoor Fan Protection

EE

Keys are locked (not failure)

E9

Full Water Protection

CC

The unit is remotely monitored or controlled
by centralized controller and the wire control-
ler’s functions are invalidated (not failure)

FF

Connected control communications

Failure

E5  Material Malfunction Will Be Showed By  The Indicator Light  On The Mother Board Of Outside Unit

SWING

TIMER

９

Summary of Contents for ASDU-09A










































Reviews:

No comments

Brands by name

Popular brands

Load more brands