This warranty does not cover damages or loss caused by:
1) Heat or light lamps.
2) Any consequential losses arising from incorrect installation or
operation or maintenance of this product.
3) Any consequential losses arising from incorrect wiring of this
product.
4) Any modifications or changes made to the unit, other than those
recommended by the Manufacturer.
MAIN TECHNICAL PARAMETERS
LIST OF PARTS
Operation unit
1000W Halogen Heat Lamp (LHT0326)
1 piece
1 piece
Installation instruction & hole-cutting template
1 piece
Backdraft stopper
1 set
Duct clip
Switch
1 piece
3 pieces
Warranty card
1 piece
Ducting kit
1 set
We reserve the rights to revise this instruction without any prior notice.
Model Number
Rated Voltage
Rated Frequency
Rated Power
230V-240V
50Hz
1100W
FAN6577
WARRANTY
The unit is warranted against defects in manufacturing and workmanship
for a period of 5 years. The warranty does not extend to lamp globes
supplied or installation of the unit or any associated wiring or any
damage caused by installation or wiring.
2. Lamp Replacement
- Shut off power before replacement.
- Use ONLY 1000W Halogen Heat Lamp for heating - LHT0326
Note:
Only use Manrose replacement bulb as listed. Using other bulbs
may damage the unit.
MAINTENANCE
1. Clean
- Shut off the power before cleaning.
- Wipe the glass shield and fascia with care using a soft cloth soaked with
a neutral detergent. Check the glass shield is not loose from the slots
regularly.
Note
: Ensure the lamps are cool enough to touch before handling.
Do not switch on/off frequently when in use. Shut off the power if in long
periods of inactivity.
2. Exhaust
‘FAN’ switch On/Off
This unit can exhaust odours and steam in a quick and efficient way by
turning on the “FAN” switch.
10. Final installation
- Install the heat lamp.
- Fit one end of the heat lamp into socket and gently push it away from
the other socket. When there is enough room, fit the other end of the
heat lamp into its socket (The heat lamp is half coated with a white
reflector. When you grasp the heat lamp with cloth or paper, face the
back of the reflector to the ceiling so you can see the heat lamp’s
filament. Not doing this will reduce performance)
- Reinsert the LED lamps.
- Check the glass shield to make sure that it is not damaged and is well
fixed on the fascia by the screws (A little movement of the glass won’t
cause any problem to the use)
- Replace the fascia with screws. Use 4 rubber clips to cover the
screws.
- Fix the switch panel to the wall.
Note:
The switch wiring should be mounted inside the wall to give the
switch an integrated built in appearance. If it is necessary to run the
wiring on the outside of the wall, use a suitable conduit and fixings to
properly located and hold the wiring used.
8. Fit the in-house end of the duct to the fan outlet, and fix the end
with duct clip.
A backdraft stopper is included in the package, fit the stopper to the fan
outlet and fix it with one duct clip. Fit the in-house end of the duct to the
stopper, and fix the end with another duct clip.
Note:
Keep the route as straight as possible.
USE
Our bathroom heater uses the halogen heating lamp (re-order code
LHT0326) as a source of heat. It also combines the functions of exhaust
and light.
1. Heat
‘HEAT’ switch On/Off
Do not touch the halogen heating lamp and the glass shield with any part
of your body when in use.
3. Lighting
‘Light’ switch On/Off
INSTALLATION INSTRUCTIONS AND HOLE-CUTTING TEMPLATE
Read and save these instructions!
Please use this card as hole cutting template 470mm x 320mm.
bathroom heater
ceiling
ceiling joist
100
100
220mm
100mm minimum clearance
is required near all ceiling joists
Socket
Heat Lamp
Reflector
0
0 0 0
0
0 0 0
0
0
Filament
9. Position the housing into the hole
Choosing the best direction to put the housing into the hole in
accordance with the position of the fan outlet. Use screws to fix the unit
onto supports (not supplied). Ensure that the unit is held securely on
all 4 sides. You may have to add supports on 2 sides in between joists
or even build a frame to secure it properly into the ceiling with supports.
Note:
Try to keep the excess wire away from the housing.
PLEASE NOTE:
The Manrose Halogen Heater Fan Light has a Triple Thermal Protection
System: The Heater FL is equipped with automatic resettable thermal
switches. If the Heater FL overheats, the unit will shut off automatically.
The unit will operate normally after cooled.
The installation must be conducted by a licensed electrician and a
suitable certificate of safety is to be issued by the electrician who
installed the unit. Warranty claims will be voided unless a certificate of
safety can be produced when required, prior to service or repair.
For warranty purposes fill out the following details and save with proof of purchase.
This infortmation must be submitted in the unlikely event that this product fails.*
MODEL NO.:
FAN6577
Purchased from:
Date of purchase:
*All warranty claims must be submitted through [email protected]
