LIVE
NEUTRAL
BLUE
BROWN
Detection Range:
Tilt down 50º
Pan left 90º
Pan right 90º
Motion Detector Head Aiming
The detector head can be 90º turned left or right by hand, it can be tilted 50º downward.
Do not use the adjuster knobs to turn the detector head.
Note:
Make sure sensor head is positioned with control knob facing towards the
ground to maintain IP rating.
Walk Test and Adjustment
• Adjust the Time knob to lowest setting, (Lux knob can be “Sun” or Moon”).
• Switch power on.
• Walk across the detection area, once the detector is triggered the lamp will turn ON for 2 seconds.
• Aim sensor to adjust detection coverage.
Knob Settings
LED floodlight has two adjustment knobs:
Lux and Time at the bottom of the detector head.
• Adjust knobs carefully with flat blade screwdriver.
TIME knob setting
• You can set the time knob from 10 sec to
about 10 min, LED flood light will turn ON the
lamp, for the time duration set after each
detection movement.
• Setting time knob to D will activate D-MODE.
LUX knob setting
• When setting the LUX knob at “MOON” PIR
activation will only operate in the dark.
• When setting the LUX knob at “SUN”, PIR
activation wll operate in any light level.
D-MODE Dusk to Dawn
• When setting the TIME knob to fully clock
wise ‘D’ setting, the motion detector of the
LED floodlight will not function.The lamp will
then operate depending on the “LUX” level.
• Set to “Moon”, lamp will illuminate from Dusk
to Dawn.
• Set to “Sun”, lamp will illuminate all day and
all night. The light will flash 3 times to confirm
D-MODE activation and deactivation.
D
10min
10sec
0
Min
10
10
sec
Turn On time adjustment
Environment lux level to turn On
Lamp turns
ON at night.
Lamp turns ON
at day & night.
Adjustments
Lux
Time
D
Auto Mode
ASSEMBLY AND INSTALLATION INSTUCTIONS
N
L
Isolation Switch
*** IMPORTANT ***
Isolate electrical supply before proceeding with the installation.
This light fitting should be installed by a registered electrician.
Recommended installation height
is 2.5 meter above ground, the
maximum detection range about
10 metre and at the angle of
about 80 degrees.
Installation Procedure:
80º
3m
10m
2.5m
10m
This light fitting is rated to IP55. This means that it is suitable for use in exterior
locations. Please ensure the desired location does not exceed this rating.
Connect the cable to the terminal block as follows
(see connection diagram).
Ensure the connections are secure.
Connection
230V
1.
Switch off the power.
5.
Feed the power cable
through the rubber gasket of
the junction box. Pierce the
gasket, do not cut or slice it.
Star washer
Hand screw
9.
Attach the device to the
U bracket with star washers,
aim then tighten the screws
on both sides.
10.
Connect device to the mains.
Unit goes into warm-up period for
35-45secs.
6.
Attach the strain relief
to the device and tighten
screws firmly.
LIVE
NEUTRAL
BLUE
BROWN
7.
Connect the individual wires to
the appropriate terminal then
tighten the screw.
Push
1
2
“Click”
8.
Attach the rear cover to
the device. Ensuring it clicks
firmly into place.
2.
Marking the
screw hole.
4.
Fix the U bracket to
the wall.
φ 6mm
3.
Drill and push the screw
peg into the hole.
PIR Lens Masking
The purpose of the lens mask is to block out
areas not desired for detection. Apply to PIR
lens as required for your location.
Mounting Srews:
(M4 x 32mm) x 2
Mounting Srews:
(M3 x 12mm) x 2