manualshive.com logo in svg

Simrad GO XSE Series, Operator'S Manual

The Simrad GO XSE Series offers exceptional navigational capabilities and advanced features. Ensure seamless installation with the comprehensive "Installation Manual" available for "free download" at manualshive.com. This detailed "manual" provides step-by-step instructions for setting up your device, optimizing your experience on the water.

Share
Download
background image

Weather

About the weather feature

The system includes weather functionality that allows the user to
view forecast data overlaid on the chart. This helps gaining a clear
understanding of the weather conditions that are likely to appear.
The system supports weather data in GRIB format, available for
download from various weather service suppliers.
The system also supports weather data from SIRIUS Marine Weather
Service. This service is available only in North America.

Wind barbs

The rotation of the wind barbs indicate the relative wind direction,
with the tail showing the direction the wind is coming from. In the
graphics below, the wind comes from the northwest.
Wind speed is indicated by a combination of small and large barbs
at the end of the wind tail.

Zero knots / Indeterminate wind direction

Small barb = 5 knots

Large barb = 10 knots

Arrow barb = 50 knots

If a combination of 5 and 10 knot barbs are shown on a tail, then
add them together to give you the total wind speed. The example
below shows 3 x large barb + 1 x small barb = 35 knots, and 60
knots indicated with 1 x arrow barb + 1 x large barb.

Wind speed: 35 knots

Wind speed: 60 knots

20 

186

Weather

 | GO XSE/XSR Operator Manual

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

MacDon C Series Unloading And Assembly Instructions preview
C Series
Brand: MacDon Pages: 17
Olympus C Series Instructions Manual preview
C Series
Brand: Olympus Pages: 50
VAHVA C Series Operating And Safety Manual preview
C Series
Brand: VAHVA Pages: 19
Eclipse Combustion 6500 Instruction Manual preview
6500
Brand: Eclipse Combustion Pages: 46
Bard Duet Instructions For Use preview
Duet
Brand: Bard Pages: 2
Cadman 6010 Operator And Maintenance Manual preview
6010
Brand: Cadman Pages: 66
ParaBody 875 Assembly Instruction Sheet preview
875
Brand: ParaBody Pages: 5
Baileigh Industrial TN-300 Operator'S Manual preview
TN-300
Brand: Baileigh Industrial Pages: 28
Baileigh Industrial BP-3305CNC Operator'S Manual preview
BP-3305CNC
Brand: Baileigh Industrial Pages: 56
Hammer FR Series Operation And Maintenance Manual preview
FR Series
Brand: Hammer Pages: 42
Fellowes SafeCut Atom User Manual preview
SafeCut Atom
Brand: Fellowes Pages: 20
jablotron UC-280 Instructions preview
UC-280
Brand: jablotron Pages: 2
jablotron JA-80S Quick Start Manual preview
JA-80S
Brand: jablotron Pages: 2
Yamaha Motif-Rack XS Code List preview
Motif-Rack XS
Brand: Yamaha Pages: 48
Ublox EVK-M8F-0-00 User Manual preview
EVK-M8F-0-00
Brand: Ublox Pages: 22
Veit Brisay BX 1000 Handbook preview
BX 1000
Brand: Veit Brisay Pages: 18
Sailor 500 FleetBroadband User Manual preview
500 FleetBroadband
Brand: Sailor Pages: 20
Jandy AquaPure Installation And Operation Manual preview
AquaPure
Brand: Jandy Pages: 52

Brands by name

Popular brands

Load more brands