Simrad AP35 Instruction Manual Download Page 78 | Manualshive

Page: 78 / 104

background image

Simrad AP35 Autopilot

76

22083083H

INSTALLATION

Turn rudder

max. STBD

034 Adjust?

The value shown on the display is the value read by the feedback unit before
any adjustment is made. The arrow indicates to which side the rudder is
positioned. If the displayed angle is different from the actual angle, set
correct rudder angle on the display by turning course selector clockwise to
increase the value or counter clockwise to decrease the value.

Note !

If the rudder feedback is mounted upside down, the displayed rudder angle
may be to the wrong side before you start the adjustment (arrow pointing to
Port).

Advance to the next step by pressing the STBD [>] button

INSTALLATION

Turn rudder

max. PORT

030 Adjust?

Manually turn the helm wheel to port until the rudder stops at maximum port
rudder.

INSTALLATION

Turn rudder

max. PORT

039 Adjust?

Adjust the displayed angle the same way as for starboard adjustment. (This
time you need not correct for wrong side if the Rudder Feedback is upside
down).

Note !

Rudder zero may still be wrong but will be adjusted later during Sea Trial.

Proceed to next menu item by pressing STBD [>] button.

INSTALLATION

Center Rudder

Automatic

rudder test ?

The display will alternate between Center Rudder and current rudder angle
as long as the rudder is more than 10

°

out of midship.

«
...
76
77
78
79
80
...
»

Summary of Contents for AP35









































































































Reviews:

No comments

Related manuals for AP35

Xsential QUAD-RO

Brand: Watermark Pages: 8

Brand: PURE Pages: 88

EZH2O LZWS-LRPBM28K

Brand: Elkay Pages: 4

Diamond Products GTXR+

Brand: HydraMaster Pages: 49

Coldrink 1-MC2 System EV9612-56

Brand: Everpure Pages: 2

Brand: Samsung Pages: 18

Brand: Samsung Pages: 23

Brand: Samsung Pages: 11

SoundTower TW-H5500

Brand: Samsung Pages: 20

Brand: Samsung Pages: 34

Brand: Sony Pages: 2

Brand: Sony Pages: 112

Brand: LOG Pages: 11

Brand: Aiwa Pages: 60

Brand: Akai Pages: 23

Brand: Akai Pages: 45

Brand: Akai Pages: 36

MAADHURIUM DIGITAL HARMONIUM

Brand: Radel Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands