Simpson GCN-MEP Operator'S Manual Download Page 2

T-SAS-GCNM12  ©

2012 Simpson Strong

-T

ie Company Inc.

-1-

SAfETY STARTS WITH YOU

A. TRAINING

 1.   Simpson Strong-Tie recommends obtaining training and reading this 

operator’s manual before attempting to use this tool. Training is available at 

www.strongtie.com/training, or by calling 1-800-999-5099. Obtaining this 

instruction is 

YOUR RESPONSIBILITY.

 2.  Read this manual completely and understand its contents fully before 

attempting to operate the tool. If there is anything in this manual that 

 

you do not fully understand, ask your instructor or call Simpson 

 

Strong-Tie at 1-800-999-5099 for information. Reading and understanding 

this manual is 

YOUR RESPONSIBILITY

.

B. LIMITATIONS

  1.  Just as no instruction book of any kind can forewarn against all possible 

situations or emergencies that may arise, neither can Simpson Strong-Tie 

instructors or printed instructions detail all possible conditions 

 

or circumstances surrounding the use of this tool or its supporting products. 

Recognizing these circumstances and reacting in a safe manner is 

 

YOUR RESPONSIBILITY

.

  2.  Simpson Strong-Tie disclaims any responsibility for injury or death, which 

may result from any disregard of this manual or the verbal instruction of 

the authorized Simpson Strong-Tie instructor. Following the rules of safe 

operation is 

YOUR RESPONSIBILITY

.

SAFETY STARTS WITH YOU!  

OBTAIN AUTHORIZED TRAINING

Summary of Contents for GCN-MEP





















Reviews: