background image

22

ENGINE:

5.25 Series Briggs & Stratton

Make

Briggs & Stratton

Domestic 
Model / Type

09A413 / 0202E1

CE 
Model / Type

09A413 / 0203E1

Gross Torque*

5.25 ft. lbs. @ 3060 rpm

Displacement

9.02 Cu. in (148 cc)

CHASSIS:

Spout Rotation

190 Degrees

Auger Diameter

9” (22.9 cm) 

Tire Size

7” x 1.5” (17.8 cm x 3.8 cm)

DIMENSIONS:

Effective Clearing

22” (56 cm)

Width

Length

42” (107 cm)

Height

42” (107 cm)

Weight

75 lbs (34 kg)

NOTE: Specifications are correct at time of printing and are subject to change without notice.

* The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive
Engineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been
obtained and corrected in accordance with SAE J1995 (Revision 2002-05). Torque values are derived at 3060 RPM;
horsepower values are derived at 3600 RPM. Actual gross engine power will be lower and is affected by, among
other things, ambient operating conditions and engine-to-engine variability. Given both the wide array of products on
which engines are placed and the variety of environmental issues applicable to operating the equipment, the gas
engine will not develop the rated gross power when used in a given piece of power equipment (actual "on-site" or net
power). This difference is due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust,
charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature,
humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton
may substitute an engine of higher rated power for this Series engine.

REPLACEMENT PARTS

Replacement parts are available from your authorized
dealer.  Always use genuine Simplicity Service Parts.

TECHNICAL MANUALS

Additional copies of this manual are available, as well as
fully illustrated parts lists. Technical manuals can be
downloaded from 

www.simplicitymfg.com.

Engine Oil
Touch-Up Paint
Grease Gun Kit 
8 oz. Grease Tube

Tire Sealant
Degrimer/Degreaser
Gas Stabilizer

MAINTENANCE ITEMS

Many convenient and helpful service and maintenance
items are available from you authorized dealer.  Some of
these items include:

Model:

Mfg. No.:

Your Name:

Address:

City, State, Zip:

Visa/Mastercard No.:

Card Expiration Date:

Specifications

Parts & Accessories

Summary of Contents for 1695468





























Reviews: