Simplicity 1334 Operator'S Manual Download

Page: 1 / 34

Print Vendor

Instructions

How to use this file

Operator’s Manuals

Paper Size:

• 11x17

• Body - 50 lbs brilliant white offset or equivalent

• Cover - on pre-printed two tone “Swash” stock.

Press:

• Body - 1 color, 2-sided

• Cover - 1 color, 1 sided

Bindery:

• Saddle stitch, face trim *if too thick for saddle stitch, tape bind

Covers:

• FRONT COVER is present at the beginning of the file.

• BACK COVER is the page immediately after the front cover.

• The part number for this manual (typically a 172_____ number) is

located on the front cover.

• This file may contain several manual which differ only by their covers.

See the part number at the bottom of the cover page. .

Body:

• The body for all manuals is identical regardless of the cover.

• Odd number pages are always right hand pages, even number pages

are always left hand pages.

General:

• This instruction sheet is NOT part of the manual and must not be

printed.

• Pages labeled “THIS PAGE INTENSIONALLY BLANK” are placement

pages and should NOT be printed.

Summary of Contents for 1334



































Search results

Summary of Contents for 1334

Reviews:

Related manuals for 1334

Brands by name

Popular brands

Simplicity 1334, Operator'S Manual

Search results

Summary of Contents for 1334

Reviews:

Related manuals for 1334

Brands by name

Popular brands