Features
Provides Temporal Code 4 (TC4) NAC (Notification
Appliance Circuit) control for Carbon Monoxide
(CO) gas warning:
The TC4 CO gas warning is a repeated sequence of four
cycles of 100 msec on with 100 msec off, followed by
5 seconds off per NFPA 720,
Standard for the
Installation of Carbon Monoxide (CO) Warning
Equipment in Dwelling Units
Compatible appliances includes: CO Sounder Base
4098-9798, 4901-9820 Horn (set for free-run), and 4903
Series 4-wire A/V appliances horn input (
not compatible
with SmartSync horn control appliances
)
Compatible Simplex
®
equipment NAC sources:
4100ES, 4100U, or 4010ES NAC outputs
4009 IDNet NAC Extender NAC outputs
Each module requires an input NAC that powers the 3A
rated output NAC for control of compatible audible
notification appliances only (
not for strobes
)
Three selectable operation modes:
Synchronized operation
allows a separate and
dedicated control NAC to both activate and synchronize
the Temporal Code 4 output timing of up to 20,
4905-9835 modules
Unsynchronized operation
also allows the separate and
dedicated control NAC to activate the Temporal Code 4
output timing of up to 20, 4905-9835 modules, but
without synchronization between the modules
Stand-Alone operation
allows the input NAC in alarm
to activate Temporal Code 4 timing for NACs dedicated
for CO gas alarm; no fire alarm signals are available, no
control NAC is used
For both Synchronized and Unsynchronized modes,
when the control NAC is off, the module output NACs
will follow the fire alarm signals of the input NAC
NOTE:
For TC4 output, both the input NACs and the
control NACs requires a Steady On signal
Compact, sealed construction:
Mounts in standard 4” square electrical box
Screw terminals for wiring connections
Listed to UL Standard 864 and ULC Standard S527
Description
CO gas alarm warnings
are required to be different from
fire alarm warnings. In the event of a CO gas alarm, the
presence of a Temporal Code 4 audible signal pattern
identifies the type of condition to the responders to assist in
determining the proper actions to be taken.
* This product has been approved by the California State Fire Marshal (CSFM) pursuant to
Section 13144.1 of the California Health and Safety Code. See CSFM Listing 7300-0026:328
for allowable values and/or conditions concerning material presented in this document. This
product was not accepted by MEA (NYC) as of document revision date. Additional listings
may be applicable; contact your local Simplex product supplier for the latest status. Listings
and approvals under Simplex Time Recorder Co. are the property of Tyco Fire Protection
Products.
ON
1 2
4905-9835 Temporal Code 4 Module
(shown approximately 1/2 size)
Description (Continued)
CO gas alarm, or fire alarm.
Use of the 4905-9835
Temporal Code 4 Module allows the NFPA 720 Temporal
Code 4 signal to be generated using a standard Steady On
audible appliance NAC input. Under the fire alarm panel’s
control, the audible notification signal can be selected for a
conventional fire pulse pattern for a fire alarm condition, or
the Temporal Code 4 pattern can be activated for a CO gas
alarm condition.
Specifications
NAC Control
For 24 VDC NACs, up to 3 A
maximum, limited by input NAC
rating; for control of audible
notification appliances compatible
with TC4 code pulse duty cycle
Input NAC Current
Requirements
Supervisory current = 0.18 mA
Alarm current = 15 mA
Control NAC Current
Requirements
Supervisory current = 0 mA
Alarm current = 3 mA
Mounting Distance
to input NAC Source
Mount close-nippled, 20 ft (6 m)
maximum distance
Wire Connections
Screw terminals for in/out wiring,
18 to 12 AWG wire
(0.82 to 3.31 mm
2
)
Dimensions
4” x 4
⅛
” x 1
⅜
” D
(102 mm x 105 mm x 35 mm)
Mounting Plate
Material
Sheet metal, galvanized
Temperature Range
32° to 120° F (0° to 49° C),
intended for indoor operation
Humidity Range
Up to 93% RH at 100° F (38° C)
Non-Addressable Peripherals
UL, ULC, CSFM Listed;
4905-9835 Temporal Code 4
FM Approved*
Module for CO Gas Alarm Notification
S4905-0006-5 4/2013
