IDNAC SLC Operation Advantage (Cont’d)
Reduced current allows efficient IDNAC SLC
operation.
With
IDNAC SLCs
, a
constant
29 VRMS
source voltage is maintained, even during battery standby,
allowing strobes to operate at higher voltage with lower
current and ensuring a consistent current draw and voltage
drop margin under both primary power and secondary
battery standby. Efficiencies include wiring distances up to
2 to 3 times farther than with conventional notification, or
support for more appliances per IDNAC SLC, or use of
smaller gauge wiring, or combinations of these benefits, all
providing installation and maintenance savings with high
assurance that appliances that operate during normal system
testing will operate during worst case alarm conditions.
Reducing Installation and Testing Time.
With
separate controls on the same two-wire SLC, installation
time and expense for both retrofit and new construction can
be significantly reduced. When Class B wiring is used,
wiring can be “T” tapped
, allowing more savings in
distance, wire, conduit (size and utilization), and overall
installation efficiency. Use of the magnet test feature
improves installation efficiency. TrueAlert device reports
conveniently identify information about each connected
appliance.
TrueAlert Addressable Wiring Isolator
Isolator Model
4905-9929
is available for remote
mounting on TrueAlert addressable circuits to isolate short
circuited wiring from functioning wiring. (Refer to data
sheet S4905-0001 for additional information.)
TrueAlert Addressable Diagnostics
Test Features.
Controllers can be selected to pulse each
appliance’s LED when it receives a supervision poll. When
the controller is selected for diagnostic mode, the appliance
magnet test feature provides a response at the individual
appliance being tested.
Silent Appliance Magnet Test.
In this test mode, in
response to the magnet test, the appliance LED pulses
sequentially to conveniently indicate the appliance’s address.
Operational Appliance Testing.
In this test mode, after
the address is indicated by pulsing the appliance LED, the
strobe will briefly flash to indicate proper operation.
TrueStart Instrument Two (TSIT).
The 2nd generation
of the Simplex TrueStart Test Instrument adds testing of
IDNAC SLC wiring and TrueAlert (and TrueAlert ES)
appliances to its ability to test IDCs, NACs, and IDNet
communications
before
connection to the control panel
.
Please contact your local Simplex representative for
additional information.
Service Port
Page 1
REPORT 5 : TrueAlert Device Report
12:34:56am MON 19-May-14
POINT ID
CUSTOM LABEL
DEVICE
TYPE
CANDELA
T14-1-1
Location Label . . . up to 40 characters
V/O
15
T14-1-2
Break Room 5
S/V
110
T14-1-3 Boiler
Room
S/V
75
T14-1-4
Elec. Room 7
S/V
30
2
S4906-0006-7 5/2014
Multi-Candela Addressable S/Vs
Model
Lettering
Listings
Housing Color Mounting Dimensions
Description
4906-9251 White
FIRE
UL & ULC
Red
Wall
7 ¼” H x 5” W x 2
⅝
” D
(184 mm x 127 mm x 67 mm)
Multi-Tapped
Speaker with
Multi-Candela
Addressable Strobe;
intensity selectable
as: 15, 30, 75, or 110
candela
4906-9253 Red
FIRE
White
4906-9254 Red
FIRE
UL
White Ceiling
7 ½” (191 mm) diameter speaker
housing, ½” (13 mm) deep; lens extends
2
⅝
” (67 mm) above housing;
extension into box = 2 ¾” (70 mm)
4906-9255 Blank
4906-9256 Red
ALERT
4906-9257 Red
FIRE
ULC
Wall Mount S/V Adapters, Replacement Covers, Wire Guard; Ceiling Mount Tile Bridge
Model
Description
Dimensions
4905-9946 Surface Mount Red Adapter Skirt Required when mounting to surface
mounted electrical box, 4” square, 1 ½”
deep with 1 ½” deep extension
7 ¾” H x 5
⅜
” W x 3
3
⁄
16
” D
(197 mm x 137 mm x 81 mm)
depth with S/V = 5
⅞
” (149 mm)
4905-9947 Surface Mount White Adapter Skirt
4905-9903
Adapter Plate, red, required to mount S/V on 2975-9145 mounting box
(typically for retrofit)
8
5
⁄
16
" H x 5 ¾" W x 0.060” Thick
(211 mm x 146 mm x 1.5 mm)
2975-9145
Mounting Box, red, for surface or flush mount, requires adapter plate 4905-9903
(this box may be available for retrofit applications)
7
⅞
" H x 5
⅛
" W x 2 ¾" D
(200 mm x 130 mm x 70 mm)
4905-9996 Red Wall Mount S/V Replacement Cover with white “FIRE” lettering
7 ¼” H x 5” W x 1
⅜
” D
(184 mm x 127 mm x 35 mm)
4905-9997 White Wall Mount S/V Replacement Cover with red “FIRE” lettering
4905-9998
Red Wire Guard for Wall Mount S/V; with mounting plate, compatible with surface
and semi-flush boxes (UL listed by Space Age Electronics Inc.)
8
⅜
” H x 6
1
⁄
16
” W x 3 ¼” D
(213 mm x 154 mm x 79 mm)
2905-9946 Tile Bridge for Ceiling Mount S/Vs
See diagram on page 3
Product Selection
TrueAlert Device Reports Reference
