manualshive.com logo in svg

Simkits USB Altimeter, Construction Manual

Share
Download
Simkits USB Altimeter Construction Manual Download Page 3

-

Normal SERVO

-

Modified SERVO

Remove disc and screw. 
These parts are no 
longer required.

Modify an HS300 or HS311 servo, 
or order a modified servo 
through the SimKits webshop.
See separate manual for 
instructions on modifying a servo.

41

A2

A1

Place optical 

F

 into front ring 

A1

 

en cement it by sparingly 
applying glue to the back f the 
front ring, in the edge where 
optical and front ring connect.

1

2

0.26" 
(6.5 mm.)

A6

A7

A5

A5/A6/A7

D

A8

Connect cord 

A6

 to light 

A5

 by soldering. 

Use sleeve 

A7

 to insulate the soldered 

connection, but leave roughly 8 mm's 
worth of wire free at the base of the light. 
The sleeve shrinks when heated.

Connect the wires 
to the circuit board. 
Polarities are 
not important.

Place the rotary encoder assembly's 
connector onto the circuit board 
as indicated.

Normal SERVO

Twist the servo clockwise by hand until it blocks.

Boor het linker-benedengat
(van voren af gezien) van front-
ring 

A1

 op, totdat dit een maat

heeft van 0.26" / 6.5 mm.

Page 3

9

10

11

12

13

14

15

16

S

SIMULATOR   PARTS

Altimeter Construction Manual

Summary of Contents for USB Altimeter











Reviews:

No comments

Brands by name

Popular brands

Load more brands