www.silverlinetools.com
5
168754
Electrical Safety
The wires in this product are coloured:
Blue
Neutral
Brown
Live
Green & Yellow
Earth
This appliance must be protected by a suitable fuse.
•
To prevent fire or shock hazard, do not expose this product to rain, water
•
or moisture.
There are no user serviceable parts inside except those referred to in
•
this manual.
Always refer servicing to qualified service personnel. Never remove any
•
part of the casing unless qualified to do so; this unit contains dangerous
voltages.
Use of a residual current device will reduce the risk of electric shock.
•
Dangerous environment
Do not use power tools in damp or wet conditions, or expose them to
•
rain. Provide adequate surrounding work space and keep area well lit.
Do not use power tools where there is a risk of explosion or fire from
combustible material, flammable liquids, flammable gases, or dust of
an explosive nature. When using power tools avoid contact with any
earthed items such as pipes, radiators, cookers, refrigerators, metal
baths and taps.
Protect yourself from vibration
Hand held power tools may produce vibration. Vibration can cause
•
disease. Gloves to keep the operator warm may help to maintain good
blood circulation in the fingers. Hand held tools should not be used for
long periods without a break.
Maintain your power tool
Ensure all ventilation holes are kept clear at all times. Overheating and
•
fire may otherwise result.
Always Disconnect
Before changing fittings or accessories, always ensure that your tool is
•
disconnected from the power source.
Switch off before connecting
Ensure that the power tool is switched off before connecting to the power
•
source. If the power tool stops unexpectedly, turn the power switch to off.
Do not abuse the power cord
Be sure your cable or extension cable is in good condition. Always have
•
a damaged cable or extension cable replaced at an authorised service
centre before using it. Never yank or pull the cable to disconnect it from
the power socket. Never carry your tool by its cable. Keep the cable away
from damp, heat, oil, solvents, and sharp edges.
Don’t leave the tool running unattended
Always wait until your tool has completely stopped functioning, and has
•
been unplugged, before leaving it.
Inverter
Unpacking Your Inverter
Carefully unpack and inspect your inverter. Fully familiarise yourself with
•
all features and functions of the product.
If any parts are damaged or missing, have these parts repaired or
•
replaced before use.
Placement of your inverter
• Always place the inverter on a level surface.
• Do not use the inverter in any damp environment, or any position where
the inverter could accidentally come into contact with water.
• Always position the inverter away from direct sunlight and other
heat sources. The inverter should only be used when the ambient air
temperature is between 10-30˚C.
• Allow for adequate ventilation around the inverter. There should always
be at least 25mm of clear space around the inverter. Do not place
anything on top of the inverter. Ensure that ventilation holes are not
obscured.
• Do not use the inverter in any location where flammable gases may be
present. This includes inside engine bays, and battery compartments.
Connecting to the power supply
• This inverter is supplied with a 12V supply lead (6). This allows you to
connect the inverter directly to a 12V battery.
• Do not attempt to connect the inverter to any form of 230V distribution
system (e.g. building or caravan wiring).
• The 12V system must be capable of supplying an adequate current
to the inverter. To calculate the approximate current requirement, divide
the inverter power rating (W) by 10. Consult the vehicle user manual for
electrical supply information.
• This inverter should only be used with 12V DC positive earth electrical
systems. Use with any other type of system may be dangerous and could
cause permanent damage to electrical components.
• This inverter is equipped with dual 12V input connectors. This enables
two batteries to be used to feed the inverter. The inverter can be run from
one battery, but battery life will be reduced, and the inverter may shut
down under high load.
• Remove the screws of the 12V input connecters (5) and attach one end
of each 12V supply lead to the connectors. Tighten the screws. Ensure
that the positive and negative (red and black) leads are connected to the
correct terminals as indicated on the inverter
• The free ends of the 12V supply leads can now be connected to the
battery.
• To reduce the risk of accidental short circuiting, always have the
12V supply leads securely attached to the inverter when connecting or
disconnecting the battery.
• Do not attempt to connect the inverter to the 12V supply by any other
means than the supplied connector.
1
Power indicator light
2
Low battery indicator light
3
230V output socket
4
Power switch
5
12V input connectors
6
12V supply leads
Product Familiarisation
168754_instructions.indd 5
20/8/09 10:14:10
