background image

10 GB/IE/NI

 

˜

Before use

 

˜

Unpacking

 

 

Remove the packaging . Check if the product is 

damaged .

 

˜

Assembly

 

 

Accessory needed: Cross head screwdriver

 

 

Number of persons needed for assembly: 1 adult

Fig. Step

C

1 .  Remove the knurled screw 

[

14]

 from the 

pole on the motor unit 

[

9]

 .

2 .  Place the pole on the base 

[

13]

 .

3 .  Fasten with the knurled screw 

[

14]

 .

D

Remove the 4 lock screws 

[

15]

 from the motor 

unit 

[

9]

 .

E

1 .  Align the rear grille handle 

[

5]

 upwards 

and to the rear . Attach the rear grille 

[

4]

 

to the motor unit 

[

9]

 .

2 .  Tighten with the 4 lock screws 

[

15]

 .

F

1 .  Place the blade 

[

2]

 on the motor shaft 

[

6]

 . 

Insert the pins on the motor shaft into the 

groove 

[

3]

 on the rear of the blade .

2 .  Tighten the lock cap 

[

1]

 on the motor shaft 

[

6]

 (direction of rotation:  ) .

Fig. Step

G

1 .  Remove the lock screw and the lock 

nut 

[

17]

 from the front grille 

[

18]

 .

2 .  Loosen the grille clips 

[

16]

 from the front 

grille 

[

18]

 .

3 .  Centre the hanging device 

[

19]

 of the front 

grille 

[

18]

 on the rear grille 

[

4]

 .

 

NOTE:

 The 4 grille clips 

[

16]

 must fit over 

the frame of the rear grille 

[

4]

 and the 

front grille 

[

18]

 .

H

Insert and fasten the lock screw and the lock 

nut 

[

17]

 . Close the 4 grille clips 

[

16]

 over the 

frame of the rear grille 

[

4]

 and the front grille 

[

18]

 .

 

NOTE:

 The lock screw and the lock 

nut 

[

17]

 are very small . Do not lose or drop 

these fasteners .

 

˜

Tilt adjustment

 

 

Loosen the knob 

[

12]

 .

 

 

Adjust the tilt angle manually .

 

 

Tighten the knob 

[

12]

 again .

 

 

Do not perform the tilt adjustment when the 

product is in operation .

Summary of Contents for 384782 2107
















Reviews: