background image

- 5 -

Using Your Ice Maker

Cleaning And Maintenance

1. Unpack the unit, then check and make sure that all the accessories 

including the ice basket and ice scoop are included. Please contact 

us if some accessories are missed.

2. Please ensure the unit is level and on a stable table or platform to 

avoid malfunction.

3. Only use drinking water.

4. Do not fill the water reservoir with hot water. This may damage the 

unit. It is best to fill the water reservoir with water of room tem-

perature or lower.

5. Do not use the unit in a very cold environment (lower than 

41℉/5℃

).

6. Clean the unit by following the operation of “CLEANING AND MAIN-

TENANCE” before operating.

To keep your ice tasting fresh and the unit looking great, we recom

-

mend cleaning the unit once per week.
1. Remove the ice basket.
2. Clean the unit interior with a soft cloth soaked with warm water and 

vinegar, then rinse with clean water and then drain all the water.

3. Clean the exterior of the unit with a soft damp cloth. Use a mild 

dishwashing soap, if necessary.

Before First Use

Note:

• Do not use organic solvent, boiled water, detergent, strong acid and 

strong alkali etc. for cleaning.

• Please empty the water reservoir and dry it for storage if the unit is 

not used for a long time.

• When the unit is not to be used for a long duration, drain the water 

completely & dry the interior.

• Store in a well vented area.

Summary of Contents for SLIM01G1









Reviews: