manualshive.com logo in svg

Silicon Laboratories WGM160P, User Manual, Page: 19 / 35

Share
Download
Silicon Laboratories WGM160P User Manual Download Page 19

5.4  USB Micro-B Connector

The BRD4321A radio board is equipped with a USB Micro-B connector that is connected directly to the WGM160P . 

Figure 5.4 Radio

Board USB Connector on page 19

 shows how the USB lines are connected to the WGM160P.

This USB connector may also be used to power the radio board. This is allows the radio board to be powered externally while the Wire-
less STK Mainboard can be switched completely off.

The radio board contains a voltage regulator and a transisor switch that automatically connects the regulated supply to the module pow-
er supply. The power select slide switch on the Wireless STK Mainboard should be set to 

USB

 or 

BAT

 to avoid conflict with the Main-

board power supply when using the USB connector.

USB micro B

Connector

VBUS

D+

D-

USB Micro-B

Connector

USB_DM (PF10)

USB_DP (PF11)

USB_VBUS

10 nF

 

WGM160P

Figure 5.4.  Radio Board USB Connector

5.5  MicroSD Card Slot

BRD4321A contains a microSD card slot which is connected to the WGM160P Wi-Fi Module. It enables testing of SW applications uti-
lizing a microSD or microSDHC card.

CMD_MOSI

DAT0_MISO

CLK

CD_DAT3_CS

DETECT

WGM160P

microSD Card

Connector

PB3 (USART2_TX #1)

PB4 (USART2_RX #1)

PC4 (USART2_CLK #0)

PC5 (USART2_CS #0)

PF5 (GPIO)

Figure 5.5.  microSD Card Slot

Note: 

The microSD card slot is located on the bottom side of the BRD4321A Radio Board. To install a microSD or microSDHC card,

remove the radio board from the mainboard and push the microSD or microSDHC card into the card slot with the metal contacts of the
memory card facing towards the PCB. Attach the radio board back into the Wireless STK Mainboard.
 

UG351: WGM160P Wi-Fi Module Wireless Starter Kit User's Guide

Peripherals

silabs.com

 | Building a more connected world.

Rev. 1.0  |  19

Summary of Contents for WGM160P




































Reviews:

No comments