manualshive.com logo in svg

Silicon Laboratories WGM160P, User Manual, Page: 23 / 35

Share
Download
Silicon Laboratories WGM160P User Manual Download Page 23

6.  RMII Ethernet EXP Board

The RMII Ethernet EXP Board included with the WGM160P Wireless STK includes the following features:

• 1x 100 Mbit Ethernet PHY (Microchip KSZ8091RND)
• 1x RJ45 Ethernet jack with integrated magnetics
• 1x LED for link status/activity indication

The connections between the EXP board and the WGM160P are shown in the figure below:

PE15 (ETH_RMIITXD0 #0)

CRSDV (EXP7)

PA1 (ETH_RMIIRXD1 #0)

WGM160P

RXD1  (EXP6)

TXEN  (EXP4)

MDC (EXP11)

MDIO (EXP13)

PA2 (ETH_RMIIRXD0 #0)

PE14 (ETH_RMIITXD1 #0)

PA0 (ETH_RMIITXEN #0)

PA4 (ETH_RMIICRSDV #0)

PA15 (ETH MDC #3)

PA3 (ETH_RMIIREFCLK #0)

PA6 (ETH_MDC #3)

PA5 (ETH_RMIIRXER #0)

RJ45

TXD0  (EXP14)

TXD1  (EXP12)

RXER  (EXP9)

RXD0  (EXP8)

REFCLK  (EXP10)

RJ45

KSZ8091RND

TX_P

TX_N

RX_P

RX_N

100 BASE-TX

RMII PHY

Figure 6.1.  RMII EXP Board

Note: 

Due to pin limitations on the WGM160P module, the following peripherals are not available while using the RMII Ethernet EXP

board:

• Display
• SD Card
• LEDs

 

6.1  BRD8026A Errata

Table 6.1.  BRD8026A Errata

Board Revision

Problem

Description

A00

Silk print error

EXP header pin-out table on bottom side incorrectly lists RXER on EXP3 and
CRSDV on EXP5.

The actual pin-mapping is CRSDV on EXP7 and RXER on EXP9.

UG351: WGM160P Wi-Fi Module Wireless Starter Kit User's Guide

RMII Ethernet EXP Board

silabs.com

 | Building a more connected world.

Rev. 1.0  |  23

Summary of Contents for WGM160P




































Reviews:

No comments