manualshive.com logo in svg

Silicon Laboratories EFR32xG14 Wireless Gecko, Reference Manual

The Silicon Laboratories EFR32xG14 Wireless Gecko offers exceptional wireless connectivity with advanced features. Access the comprehensive Reference Manual detailing its functionalities, capabilities, and instructions for optimal usage. Download the user manual for free from our website manualshive.com, ensuring a seamless experience with this cutting-edge product.

Share
Download
background image

Figure 4.3.  System Address Space With Peripheral Listing

The embedded SRAM is located at address 0x20000000 in the memory map of the EFR32. When running code located in SRAM start-
ing at this address, the Cortex-M4 uses the System bus interface to fetch instructions. This results in reduced performance as the Cor-
tex-M4 accesses stack, other data in SRAM and peripherals using the System bus interface. To be able to run code from SRAM effi-
ciently, the SRAM is also mapped in the code space at address 0x10000000.

When  running  code  from  this  space,  the Cortex-M4  fetches  instructions  through  the  I/D-Code  bus  interface,  leaving  the  System  bus
interface for data access.

The SRAM mapped into the code space can however only be accessed by the CPU and not any other bus masters, e.g. DMA. See

4.5 SRAM

 for more detailed info on the system SRAM.

The Sequencer RAM is used by the Sequencer for both instructions and data. This RAM is also available for general use by most AHB
masters.

Reference Manual

Memory and Bus System

silabs.com

 | Building a more connected world.

Rev. 1.1  |  44

Summary of Contents for EFR32xG14 Wireless Gecko





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EFR32xG14 Wireless Gecko

Aaeon UP Squared 6000 Edge Computing Kit User Manual preview
UP Squared 6000 Edge Computing Kit
Brand: Aaeon Pages: 59
Lantronix SISPM1040-582-LRT Quick Start Manual preview
SISPM1040-582-LRT
Brand: Lantronix Pages: 2
Lantronix SDS1101 Quick Start Manual preview
SDS1101
Brand: Lantronix Pages: 7
IDT DBP 7+4 User Manual preview
DBP 7+4
Brand: IDT Pages: 93
ZALMAN CNPS7000A Series User Manual preview
CNPS7000A Series
Brand: ZALMAN Pages: 9
NXP Semiconductors UM10301 PCA8565 User Manual preview
UM10301 PCA8565
Brand: NXP Semiconductors Pages: 54
MFJ MFJ-492 Manual preview
MFJ-492
Brand: MFJ Pages: 11
ZoneVu ZSI-450-IP Installation Manual & User Manual preview
ZSI-450-IP
Brand: ZoneVu Pages: 15
FUNcube Dongle Pro User Manual preview
Dongle Pro
Brand: FUNcube Pages: 23
VCS VIP 1000 User Manual preview
VIP 1000
Brand: VCS Pages: 118
Observint NVR16 Firmware User Manual preview
NVR16
Brand: Observint Pages: 117
Cowlacious Designs ISD CAP 275 Manual preview
ISD CAP 275
Brand: Cowlacious Designs Pages: 8
Hologic ThinPrep 3000 Operator'S Manual preview
ThinPrep 3000
Brand: Hologic Pages: 256
Thermalright Macho Rev. A (BW) Manual preview
Macho Rev. A (BW)
Brand: Thermalright Pages: 32
Eneo PNR-5332/3TB Quick Installation Manual preview
PNR-5332/3TB
Brand: Eneo Pages: 49
ADLINK Technology MCM-216 User Manual preview
MCM-216
Brand: ADLINK Technology Pages: 69
G&D DP1.2-Vision-IP-Fiber Installation And Operation Manual preview
DP1.2-Vision-IP-Fiber
Brand: G&D Pages: 240
PACOM PPRO-UR-4EDX Quick Manual preview
PPRO-UR-4EDX
Brand: PACOM Pages: 16

Brands by name

Popular brands

Load more brands