Silicon Graphics UV 20 System User'S Manual Download Page 12

Page: 12 / 70

xii

007-5900-001

About This Guide

•

Appendix A, “Power and Environmental Specifications,”

Lists input/output voltage specifications for the power supplies and also environmental
specifications for operating the system.

•

Appendix B, “Regulatory Compliance Information,”

Summarizes the product regulatory information.

•

Appendix C, “Rail Kit Installation,”

Describes the steps to install the rail kit.

•

Appendix D, “BMC Error Codes,”

Describes the BMC beep codes associated with failure conditions.

Related Publications

The following SGI and LSI documents are relevant to the UV 20 server:

•

MegaRAID

SAS Software User’s Guide

, publication number, publication number

860-0488-xx

•

SGI Foundation Software Start Here

, publication number 007-5641-xx

•

SGI Performance Suite Start Here

, publication number 007-5680-xx

•

SGI InfiniteStorage

series documentation

•

Man pages (online)

You can obtain SGI documentation (as well as the pertinent LSI books), release notes, or man
pages in the following ways:

•

Refer to the SGI Technical Publications Library at http://docs.sgi.com. Various formats are
available. This library contains the most recent and most comprehensive set of online books,
release notes, man pages, and other information.

•

You can also view man pages by typing

man

title

> on a command line.

Summary of Contents for UV 20







































































Search results

Summary of Contents for UV 20

Reviews:

Silicon Graphics UV 20, System User'S Manual, Page: 12 / 70

Search results

Summary of Contents for UV 20

Reviews: