Silca UC 199 Operating Manual Download Page 76

Page: 76 / 107

7.2 MAINTENACE OPERATIONS

•

Access to the top compartment

•

Access to bottom compartment

•

Cutter replacement

•

Belt replacement and tension adjustment

•

Replacement of the set of jaws on the Automatic clamp (Optional)

•

Fuse check and replacement

•

Electronic circuit board replacement

•

Keyboard/display replacement

•

Sensor replacement

•

Motor replacement

•

Lamp replacement

•

Condenser (motor) and/or feeder (lamp) replacement

•

Master/emergency switch replacement

•

Clock battery replacement

•

Win-Transfer program for loading/updating the machine program

7.3 ACCESS TO THE TOP COMPARTMENT

To gain access to the top compartment, proceed as follows:

1) turn off the machine and disconnect from the power supply.

2) loosen the 4 screws (U2) securing the top cover, then lift the cover off (Fig. 74).

Fig. 74

Operating Manual

UC199

Copyright Silca 2012

Summary of Contents for UC 199




































































































Search results

Summary of Contents for UC 199

Reviews:

Related manuals for UC 199

Brands by name

Popular brands

Silca UC 199, Operating Manual

Search results

Summary of Contents for UC 199

Reviews:

Related manuals for UC 199

Brands by name

Popular brands