background image

A1

D

A2

E

B1

F

B2

G1

C1

G2

C2

H

1

Phillips head screw driver

2

Stud finder for drywall installation

3

7/16" Socket and Wrench

4

(×6) M6 washer

(x1) External bubble level

(x4) M5x30 screw

(×6) M6 concrete anchor

Electric drill, 1/8" (3mm) drill bit for wood stud installation and 5/16" (8mm) masonry bit for concrete/brick 
installation

When mounting to a wall that contains wood studs, confirm dead center of the wood stud prior to installation, it is
recommended that the wood studs be a minimum of 16" apart.

(×4) Spacer

Tools Required:

INSTALLATION AND OPERATING INSTRUCTIONS

(×4) M8/M6 rectangular washer

(×4) M8×15 screw

Hardware kit:

(×4) M6×12 screw

It is recommended that two people perform the installation. Injury and/or damage can result from dropping or
mishandling the display.

(×6) M6x50 bolt

The wall structure must be capable of supporting at least the maximum load capacity as indicated. If not, the
wall must be reinforced. Proper installation procedure by yourself or a qualified service technician, as outlined in
the installation instructions, must be adhered to. Failure to do so could result in serious personal injury.

Prior to the installation of this product, the installation instructions should be read and completely understood.
The installation instructions must be read to prevent personal injury and property damage. Keep these
installation instructions in an easily accessible location for future reference.

Recommended mounting surfaces: wood stud and solid-flat concrete. If the mount is to be installed on any
surface other than wood studs, use suitable hardware (not included but commercially available).

Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could
result in damage to the display and/or damage to the mounting surface.

Do not install near heater, fireplace, air conditioning, in direct sunlight, or any other heat producing source.
Failure to do so may result in damage to the display and could increase the risk of fire.

(×4) M5×12 screw

Caution

CAUTION: The maximum load capacity is 99lbs. Use with products heavier than the maximum load capacity
may cause serious injury. See apparatus instructions.

(×4) M6×30 screw

(×4) M8×30 screw

2

Summary of Contents for Universal Tilting TV Mount - 23" to 42









Reviews: