SIIG aurora Quick Installation Manual Download Page 2

System Requirements

Pentium II Class computer with an AGP slot

Windows 95b or later

Windows NT 4.0 Service Pack 3 or later

32 MB system memory

Resolution and Color Depth

The Aurora AGP comes with either 16MB or 32MB of memory
installed on-board.  The chart below describes the colors and
resolutions it supports:

Resoultion

     16MB

32MB

640x480

     16.7M

16.7M

800x600

     16.7M

16.7M

1024x768

     16.7M

16.7M

1280x1024

     16.7M

16.7M

1600x1200

     (NT & W2K only) 16.7M

1920x1440

      n/a

(NT Only)

Board Layout

Technical Support

Web Site

Visit SIIG’s Web site at www.siig.com for more product features,
drivers updates, upgrade solutions, FAQs, and where-to-buy
information.

Technical Support Department

For additional support, SIIG's Technical Support Specialists are
available from 8:00 a.m. to 5:00 p.m. Monday through Friday,
Pacific Standard Time.

e-mail:

[email protected]

Telephone: (510) 353-7542

Return Merchandise Authorization (RMA) Department

If the Technical Support Specialist determines that the product
may be defective, you can return it for repair or replacement.

Step 1: Call SIIG's RMA Department
Call the RMA Department at (510) 413-5333  for a Return
Merchandise Authorization (RMA) number. Please have the
product serial number available.  It is located on the side of the
box and on the back of the product.

Step 2: Complete the RMA form

• Fill out your Return Merchandise Authorization (RMA) form,

and include it in the package along with the original materials.

• Clearly write your RMA number on the outside of the returned

shipping package and on the accompanying RMA form.

SIIG will refuse to accept any shipping package, and not
be responsible for a product returned without a RMA
number posted on the outside of the shipping carton.

Step 3: Ship the 

Aurora AGP 16MB/32MB

You are responsible for the cost of shipping the product back to
SIIG at the following address:

SIIG, Inc.      RMA#_______________
6078 Stewart Ave.
Fremont, CA 94538

SIIG will ship the repaired or replaced the product via UPS
Ground or US Mail at no cost to you.

2

15-pin Analog
Video Connector

Multimedia
VGA Chip with
heat sink

34-pin Feature
Connector

Figure 1: Board Layout

11

Summary of Contents for aurora

Page 1: ...of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are design...

Page 2: ...determines that the product may be defective you can return it for repair or replacement Step 1 Call SIIG s RMA Department Call the RMA Department at 510 413 5333 for a Return Merchandise Authorization RMA number Please have the product serial number available It is located on the side of the box and on the back of the product Step 2 Complete the RMA form FilloutyourReturnMerchandiseAuthorization ...

Page 3: ... other connected peripheral devices 2 Unplug the power cord from the back of the computer 3 Remove your computer s cover by removing its mounting screws and sliding off the cover 4 Remove any existing video graphics adapters that may be in the system Disable the motherboard s built in video if there is one 5 Remove the slot bracket by unscrewing the holding screw and sliding it out Save this screw...

Page 4: ...isplay drivers and related files 1 When Windows first restarts after installing the card Plug and Play will inform you that it has detected a new video adapter Click Next to install Standard PCI Graphic Adapter VGA Click Finish and Yes to restart the system 2 Insert the Daytona Software Driver CD into the CD ROM drive 3 AutoRun should start automatically If AutoRun does not start go to Windows mai...

Reviews: