manualshive.com logo in svg

SignalFire Sentinel-485 Series, Interface Manual

Share
Download
SignalFire Sentinel-485 Series Interface Manual Download Page 16

 

 

16

 

SignalFire Telemetry 

Rev 1.7 

Configuration / Debug 

 
 

 

WARNING: Only connect to the debug port in a safe area! 

 
 

Debug and configuration information is available if a connection is made via the debug port on the main 
board. A USB converter cable (available from SignalFire) must be used for this interface. 
 
Debug and advanced configuration may be done using the SignalFire Toolkit PC application. 

 
 

Technical Support and Contact Information 

SignalFire Telemetry 
140 Locke Dr, Suite B 
Marlborough, MA 01752 
(978) 212-2868 

[email protected]

 

 
 
 
 
 
 
 
 
 
Revision History 

 
 

  

 

Revision 

Date 

Changes/Updates 

1.1 

10/09/12 

Initial release 

1.2 

11/7/14 

Updated entity parameters 

1.3 

6/5/15 

Updated design 

1.4 

8/1/16 

Added section on Encryption 

1.5 

3/6/17 

Added graphs for sensor voltage  

1.6 

9/13/17 

Updated warnings  

1.7 

1/17/2019 

Updated low battery register to general status register 
Minor formatting updates 

Summary of Contents for Sentinel-485 Series


















Reviews:

No comments

Brands by name

Popular brands

Load more brands