background image

-17- 

PARTS 

The following parts are available from Signal Vehicle Products: 

* CAUTION:  This is not a standard telephone cable and 

CANNOT be replaced with one. 

 

LIMITED WARRANTY 

Signal Vehicle Products warrants this new product to be free from defects in material and 

workmanship, under normal use and service, for a period of one (1) year from the date of 
delivery to the first user-purchaser. 

During this warranty period the obligation of Signal Vehicle Products is limited to 

repairing or replacing, as Signal Vehicle Products may elect, any part or parts of such 
product which after examination by Signal Vehicle Products is determined to be defective in 
material and/or workmanship. 

This warranty does not cover labor charges for removal or re-installation of the product.  

Fuses and lamps are not covered under this warranty. 

This warranty does not extend to any unit that has been subjected to abuse, misuse, 

improper installation or which has not been adequately maintained, nor to units which have 
problems related to service or modification at any facility other than the manufacturer. 

 

THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT 

NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS 
FOR A PARTICULAR PURPOSE.  IN NO EVENT SHALL SIGNAL VEHICLE PRODUCTS 
BE LIABLE FOR ANY LOSS OF PROFITS OR ANY INDIRECT OR CONSEQUENTIAL 
DAMAGES ARISING OUT OF ANY SUCH DEFECT IN MATERIALS OR WORKMANSHIP. 

 

RETURN 

If you have any questions concerning this or any other SVP product, please contact 
our 

Customer Service Department

 at (585) 226-9025. 

If a product must be returned for any reason, please contact our Customer Service 
Department to obtain a Returned Goods Authorization number (RGA#) before you 
ship the product to SVP.  Please write the RGA# c learly on the package near the 
mailing label.

 

 

Part

 

Description

 

P30235-4 

Siren Top Cover 

P30234-4 

Siren Bottom Mounting Plate 

SWH-37 

Wiring Harness 

P30069-38 

Microphone Bracket with Screws 

P30053-31 

Amplifier Case Screws 

P30028-8 

5 Amp Automotive Blade Fuse for Control Head 

P30028-1 

20 Amp Automotive Blade Fuse for Amplifier 

P30232-1 

Noise Cancelling Microphone 

P30208-10 

Microphone Strain Relief 

P30032-8 

TIP36C Power Transistor 

P30239-1 

Rotary Selector Switch Knob 

P30239-2 

PA Volume Knob 

P30148-8 

Communications Cable* 

Summary of Contents for SS730





















Reviews: