Signal Hound USB-SA44B User Manual Download Page 18

Warranty and Disclaimer |

 

Warranty Service

 

14 

7.2

 

WARRANTY SERVICE 

For warranty service or repair, this product must be returned to Test Equipment Plus.  The Buyer shall 
pay  shipping  charges  to  Test  Equipment  Plus  and  Test  Equipment  Plus  shall  pay  UPS  Ground,  or 
equivalent,  shipping  charges  to  return  the  product  to  the  Buyer.    However,  the  Buyer  shall  pay  all 
shipping  charges,  duties,  and  taxes,  to  and  from  Test  Equipment  Plus,  for  products  returned  from 
another country. 

7.2.1

 

Limitation of Warranty 

The  foregoing  warranty  shall  not  apply  to  defects  resulting  from  improper  use  by  the  Buyer,  Buyer-
supplied  software  or  interfacing,  unauthorized  modification  or  misuse,  operation  outside  of  the 
environmental  specifications  for  the  product.    No  other  warranty  is  expressed  or  implied.    Test 
Equipment  Plus  specifically  disclaims  the  implied  warranties  or  merchantability  and  fitness  for  a 
particular purpose. 

7.2.2

 

Exclusive Remedies 

The remedies provided herein are the Buyer’s sole and exclusive remedies.  Test Equipment Plus shall 
not be liable for any direct, indirect, special, incidental, or consequential damages,  whether based on 
contract, tort, or any other legal theory. 

7.2.3

 

Certification 

Test  Equipment  Plus  certifies  that,  at  the  time  of  shipment,  this  product  conformed  to  its  published 
specifications. 

7.2.4

 

Credit Notice 

Windows® and Excel® are  registered  trademarks  of  Microsoft  Corporation  in  the  United  States  
and  other  countries.  

Summary of Contents for USB-SA44B



















Reviews: