background image

 

TOUCH OPERATING PANEL 

HZS 772 

 

15.07.2020 

Page 33 

13  Cleaning the Touch Screen 

CAUTION!

 

Before cleaning the touch screen, the terminal must first be turned off to avoid unin-

tentionally triggering functions or commands!

 

 
The terminal's touch screen can only be cleaned with a soft, damp cloth. A screen cleaning 
solution such as an anti-static foam, water with a mild detergent or alcohol should be used 
to dampen the cloth. The cleaning solution should be sprayed onto the cloth and not directly 
on the terminal. The cleaning solution should not be allowed to reach the terminal electron-
ics, for example, through the ventilation slots. 
 
No  erosive  cleaning  solutions,  chemicals,  abrasive  cleansers  or  hard  objects  that  can 
scratch or damage the touch screen may be used. 
 
If the terminal comes in contact with toxic or erosive chemicals, carefully clean the terminal 
immediately to prevent corrosion! 
 

To ensure the optimal function of the terminal, the touch screen should be cleaned at 

regular intervals!

 

 

To extend the lifespan of the touch screen as much as possible, using the fingers to 

operate the terminal is recommended.

 

 

Summary of Contents for 05-895-772





































Reviews: