SIGLENT SSG3000X Service Manual Download Page 27 | Manualshive

Page: 27 / 38

background image

SIGLENT

SSG3000X Service Manual 27

Test Procedures

1. Synchronize the SSG3000X and signal analyzer. Connect the RF output

terminal of the SSG3000X with the RF input terminal of the signal analyzer.
Connect the USB DEVICE connector of the SSG3000X with the USB
interface of the PC as shown in figure.

2. Install the EasyIQ software to the PC. Configure the IQ modulation wave

table using the EasyIQ softwave.

3. Configure the wave Data Source

、

the modulation type of the wave

、

the filter

parameter of the wave.

Then download the currently generated wave to the SSG3000X.

4.  Configure the SSG3000X:
a)  Set the frequency to 800 MHz.
b)  Set the level to 3 dBm.
c)  Press I/Q to enter the I/Q source settings interface.
d)  Enable the I/Q state switch.
e)  Set the source to internal.

«
...
25
26
27
28
29
...
»

Summary of Contents for SSG3000X







































Reviews:

No comments

Related manuals for SSG3000X

Brand: Eberg Pages: 14

Brand: Champion Power Equipment Pages: 38

Brand: Pal Manufacturing Pages: 15

Brand: General Air Products Pages: 34

PowerPact G0069981

Brand: Generac Power Systems Pages: 36

Brand: Onan Pages: 108

Brand: Circutor Pages: 108

Brand: Ceyear Pages: 183

Brand: Century Mark IV Pages: 6

Brand: Whisper Tech Pages: 98

Brand: Micro Innovations Pages: 2

Brand: iPower Pages: 2

Brand: iPower Pages: 2

RF MultiGen 0406-900-000

Brand: Stryker Pages: 57

Brand: SpectronIQ Pages: 57

Brand: IBEA Pages: 148

MilCom Surface Station 6000S

Brand: Ocean Technology Systems Pages: 32

DPC-7900 Series

Brand: Daewoo Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands