SIG Ryan S-T Operating, Assembly Instructions And Parts List Download Page 7

WARRANTY: 

Herr Engineering Corp. guarantees this kit to be free from defects in both materials and workmanship at the 

time of purchase. This warranty does not cover any component damaged buy use or modification. In no case shall Herr 
Engineering Corporation's liability exceed the original cost of the purchased kit. Further Herr Engineering Corp. reserves the 
right to change or modify this warranty without notice. 
In that Herr Engineering Corporation has no control over the assembly or use, no liability shall be assumed or accepted for any 
damage resulting from the use by the user during construction of the kit or the use of the final user assembled product. By the 
act of building this kit and/or using the final user assembled product, the user accepts all liability. 
If the buyer and/or user is not prepared to accept all of the liability associated with this product, he is advised to immediately 
return this kit in new and unused condition to the place of purchase for a full refund.

© Copyright SIG Mfg. Co., Inc.

SIG MFG. CO., INC............Montezuma, Iowa 50171-0520

 

LIMIT OF LIABILITY:

 

In use of our products, Sig Mfg. Co.'s only obligation shall be to replace such quantity of the product proven to be defective. 
User shall determine the suitability of the product for his or her intended use and shall assume all risk and liability in connection 
therewith.

Summary of Contents for Ryan S-T








Reviews: