SIG HRR111 Assembly Instruction Manual Download Page 9 | Manualshive

Page: 9 / 9

SIG HRR111 Assembly Instruction Manual Download Page 9

.

WARRANTY

Herr Engineering Corp. guarantees this kit to be free from defects in both materials and
workmanship at the time of purchase. This warranty does not cover any component damaged buy
use or modification. In no case shall Herr Engineering Corporation's liability exceed the original cost
of the purchased kit. Further Herr Engineering Corp. reserves the right to change or modify this
warranty without notice.
In that Herr Engineering Corporation has no control over the assembly or use, no liability shall be
assumed or accepted for any damage resulting from the use by the user during construction of the
kit or the use of the final user assembled product. By the act of building this kit and/or using the final
user assembled product, the user accepts all liability.
If the buyer and/or user is not prepared to accept all of the liability associated with this product, he is
advised to immediately return this kit in new and unused condition to the place of purchase for a full
refund.

© Copyright SIG Mfg. Co., Inc.

SIG MFG. CO., INC............Montezuma, Iowa 50171-0520

LIMIT OF LIABILITY:

In use of our products, Sig Mfg. Co.'s only obligation shall be to replace such quantity of the product proven to be defective.
User shall determine the suitability of the product for his or her intended use and shall assume all risk and liability in connection
therewith.

«
...
7
8
9

Summary of Contents for HRR111










Reviews:

No comments