Sifos Technologies PhyView PVA-3000 Reference Manual Download Page 41 | Manualshive

Page: 41 / 134

background image

PVA-3000 Reference Manual

December 2, 2019

Sifos Technologies

Page
41

3.

PVA Interactive Software

PVA Interactive

is the graphical user interface for the PhyView Analyzer. It is a Tcl/Tk application that is built from

a number of Tcl/Tk scripts. It exclusively uses the PowerShell PSA API for all instrument interactions and control
meaning that anything that can be done in PVA Interactive can also be done in PowerShell PSA.

3.1.

Overview of Menus

PVA Interactive consists of two menus that are always present.
The PVA Interactive

Main Menu

provides full access to all test

port resources including port configuration, link configuration,
impairment control, metering, calibrations, and automated
testing. Test port subsystems are all organized by category on
tabbed sub-menus that allow arbitrary navigation through test
port resources. These subsystems include:



Port & Impairment Configurations



Link Configuration



Link Monitor



PVA Meters



PVA Packet Flow



PHY Performance Tests



PVA Meter Calibrations

Generally, the Main Menu always operates on the currently selected test port within the currently connected PVA
instrument.

Separately, a

Slot-Port Select

menu allows selection of any available test port in the currently connected instrument.

This means that the test port can be altered independent of any tab menu selections in the Main Menu at any time.

3.2.

Initial PVA Connection

When PVA Interactive is opened, the user will be prompted to select an instrument to which PVA Interactive will
initially connect

(see Figure 3.2)

. The default selection will be the

most recently

connected PhyView Analyzer. This

brief dialog assures that various users on a common network sharing
multiple instruments can connect to an instrument without interfering
with other instruments that might be in use by other host computers. It
also assures that any

selected

analyzer to be utilized is powered up and

connected to the local network.

The

PVA Chassis Selection

dialog (

Figure 3.2

) verifies the presence of

any selected or entered PVA address, inventories the selected instrument
for available PVA test ports, and allows users to add any new
instruments that may have been recently connected to the network.

Note

:

If the PVA Chassis Selection dialog

fails to find a connected and

available PVA

instrument

, it will ultimately open PVA Interactive in

Demo Mode

. When the application opens in Demo Mode, the

annotation

*DEMO MODE*

will appear in red on the Slot-Port selection

menu. Demo Mode is described in Section 3.14 below.

3.3.

The PVA Main Menu

After selecting and connecting to a PVA Chassis address, the

Main Menu

(

see Figure 3.3

) will appear along with the

Slot-Port Control helper menu. The Main Menu will open by default to the first tab sub-menu,

Port Config

. Each of

the tab sub-menus will be addressed in Sections 3.6 through 3.13 below.

Figure 3.2

PSA Connection Dialog

Figure 3.1

PVA Interactive 4.2 Startup

«
...
39
40
41
42
43
...
»

Summary of Contents for PhyView PVA-3000







































































































































Reviews:

No comments

Related manuals for PhyView PVA-3000

Brand: Medeli Pages: 14

Brand: Omer Pages: 2

Brand: Keller Pages: 6

Brand: DayTronic Pages: 54

Brand: Bacharach Pages: 2

Brand: Bachmann Pages: 33

Brand: Cablescan Pages: 58

Brand: Camille Bauer Pages: 62

Brand: DAKOTA ULTRASONICS Pages: 48

Brand: TE Connectivity Pages: 9

Brand: JGR Pages: 12

Brand: National Instruments Pages: 85

Brand: National Instruments Pages: 12

Brand: National Instruments Pages: 18

Brand: National Instruments Pages: 12

Professional Plus

Brand: YSI Pages: 28

Brand: H-Star Pages: 36

Brand: King Instrument Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands