Sierra Wireless AirPrime WP7504 Hardware Integration Manual Download Page 21

Rev 1  Apr.16

21

Specifications subject to change

5

5: Regulatory Compliance and Industry 
Certifications

Important Notice

Due to the nature of wireless communications, transmission and reception of data 
can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be 
totally lost. Although significant delays or losses of data are rare when wireless 
devices such as the Sierra Wireless modem are used in a normal manner with a 
well-constructed network, the Sierra Wireless modem should not be used in 
situations where failure to transmit or receive data could result in damage of any 
kind to the user or any other party, including but not limited to personal injury, 
death, or loss of property. Sierra Wireless accepts no responsibility for damages 
of any kind resulting from delays or errors in data transmitted or received using 
the Sierra Wireless modem, or for failure of the Sierra Wireless modem to 
transmit or receive such data.

Safety and Hazards

Do not operate your AirPrime WP7504 Embedded Module:

In areas where blasting is in progress

Where explosive atmospheres may be present including refueling points, fuel 
depots, and chemical plants

Near medical equipment, life support equipment, or any equipment which 
may be susceptible to any form of radio interference.

In such areas, the AirPrime WP7504 modem 

MUST BE POWERED OFF

Otherwise, the AirPrime WP7504 modem can transmit signals that could interfere 
with this equipment.

In an aircraft, the AirPrime WP7504 modem 

MUST BE POWERED OFF

Otherwise, the AirPrime WP7504 modem can transmit signals that could interfere 
with various onboard systems and may be dangerous to the operation of the 
aircraft or disrupt the cellular network. Use of a cellular phone in an aircraft is 
illegal in some jurisdictions. Failure to observe this instruction may lead to 
suspension or denial of cellular telephone services to the offender, or legal action 
or both.

Some airlines may permit the use of cellular phones while the aircraft is on the 
ground and the door is open. The AirPrime WP7504 modem may be used 
normally at this time.

Summary of Contents for AirPrime WP7504

























Reviews: