background image

Safety instructions    

en

7

:

Warning

Risk of fire/material damage/

damage to the appliance!

The use of extension cords or 

power strips may result in fire 

due to overheating or short 

circuiting.

Connect the appliance directly 

to an earthed socket that has 

been correctly installed. Do not 

use extension cords, power 

strips or multi-way couplers.

:

Warning

Risk of injury/material 

damage/damage to the 

appliance!

The appliance may vibrate or 

move when in operation, 

potentially resulting in injury 

or material damage.

Place the appliance on a 

clean, even, solid surface 

and, using a spirit level to 

guide you, level it with the 

screw-in feet.

Risk of injury/material damage/damage to the appliance!

If you take hold of any of the 

appliance's protruding parts 

(e.g. the appliance door) in 

order to lift or move it, these 

parts may break off and 

cause injury.

Do not take hold of any of 

the appliance's protruding 

parts in order to move the 

appliance.

:

Warning

Risk of injury!

The appliance is very heavy. 

Lifting it may result in injury.

Do not lift the appliance on 

your own.

Risk of injury!

The appliance has sharp 

edges on which you could 

cut your hands.

Do not take hold of the 

appliance by its sharp 

edges. Wear protective 

gloves to lift it.

Risk of injury!

If the hoses and mains 

cables are not correctly 

routed, they may constitute a 

tripping hazard, which may 

result in injury.

Route hoses and cables 

such that they do not 

constitute a tripping hazard.

Caution!

Material damage/damage to 

the appliance

If the water pressure is too 

high or too low, the 

appliance may not be able to 

operate properly, and it may 

also result in material 

damage or damage to the 

appliance.

Make sure that the water 

pressure in the water supply 

facility is at least 

100 kPa (1 bar), and does 

not exceed 

1000 kPa (10 bar).

Material damage/damage to the appliance

If the water hoses are altered 

or damaged, this may result 

in material damage or 

damage to the appliance.

The water hoses must not be 

kinked, crushed, altered or 

severed.

Material damage/damage to the appliance

Summary of Contents for WD15G442DN

















































Reviews: