Siemens Synco living Operating Instructions Manual Download Page 77 | Manualshive

Page: 77 / 100

background image

77 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Main menu > Settings > Faults > Fault input X > Fault text:

Main menu > Settings > Faults > Fault input X > Fault priority:

Main menu > Settings > Faults > Fault input X > Fault release:

Main menu > Settings > Faults > Fault input X > Fault stat mess dly:

Main menu > Settings > Faults > Fault input X > Normal position:

Fault

input

1 2 3 4

FS fault text

Fault inp1 Fault inp2 Fault inp3 Fault inp4

Fault

text

FS fault priority

Not urgent Not urgent Not urgent Not urgent

Fault priority

Urgent

N. urg.

Urgent

N. urg.

Urgent

N. urg.

Urgent

N. urg.

FS

fault

release

Always Always Always Always

Fault release

Always

DA

Always

DA

Always

DA

Always

DA

FS fault stat mess dly.

00.05

00.05

00.05

00.05

Fault status message delay

FS

normal

position

Open Open Open Open

Normal position

Open

Closed

Open

Closed

Open

Closed

Open

Closed

Fault

input

5 6 7 8

FS fault text

Fault inp5 Fault inp6 Fault inp7 Fault inp8

Fault

text

FS fault priority

Not urgent Not urgent Not urgent Not urgent

Fault priority

Urgent

N. urg.

Urgent

N. urg.

Urgent

N. urg.

Urgent

N. urg.

FS fault release

Always

Always

Always

Always

Fault release

Always

DA

Always

DA

Always

DA

Always

DA

FS fault stat mess dly.

00.05

00.05

00.05

00.05

Fault status message delay

FS normal position

Open

Open

Open

Open

Normal position

Open

Closed

Open

Closed

Open

Closed

Open

Closed

FS Factory

setting

N. urg.

Not urgent

DA During

absence

Fault outputs 1 and 2

To forward fault status messages or to indicate them on the control panel with
a lamp, for instance, 2 fault outputs can be configured.

The fault outputs must have been activated when commissioning the
plant, and the required relay output must be connected to the central
apartment unit so that the settings described here can be made. For
the relevant descriptions, refer to document ”Mounting and Commis-
sioning (CE1C2707en)“.

Main menu > Settings > Faults > Fault output X > Fault priority:

Main menu > Settings > Faults > Fault output X > Fault source:

«
...
75
76
77
78
79
...
»

Summary of Contents for Synco living





































































































Reviews:

No comments

Related manuals for Synco living

Brand: Watts Pages: 2

ETP-MT/R OP SOLAR

Brand: Talk-a-Phone Pages: 5

Brand: Olsberg Pages: 68

Brand: VAT Pages: 39

Brand: Samson Pages: 124

Brand: Samson Pages: 86

Brand: VAC Pages: 5

Brand: UniPOS Pages: 51

Brand: Unipulse Pages: 126

Brand: YachtSafe Pages: 3

Brand: Anilam Pages: 31

Brand: Rinnai Pages: 7

Controller CR100

Brand: Sonos Pages: 2

Brand: Kelly Pages: 37

Brand: Samson Pages: 44

Brand: Hansen Pages: 12

Ames Colt Series

Brand: Watts Pages: 8

Brand: CAME Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands