Siemens Synco living Operating Instructions Manual Download Page 31 | Manualshive

Page: 31 / 100

background image

31 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Antilime function

To prevent valves and pumps from seizing, the controller periodically drives all
valves to their fully open positions and activates all connected pumps in a
stepwise fashion at predefined points in time.

Main menu > Apartment > Antilime > Antilime function:

Main menu > Apartment > Antilime > Weekday:

Main menu > Apartment > Antilime > Time of day:

Antilime

function

Weekday

Time of day

Guide value

All-year

Monday

10:00

Your setting

--- (never)

All-year

In winter operation

In summer operation

Monday

Tuesday

Wednesday

Thursday

Friday

Saturday

Sunday

…… : ……

Outside temperature heating limit

Set the outside temperature (-5..25 °C) below which heating mode is enabled.
Heating mode is locked above the set temperature. The outside temperature
heating limit also serves to change over to summer operation.

Main menu > Apartment > Settings > OT heating limit:

Factory setting

--- (Inactive – no heating limit)

Setting

………………°C

Outside temperature cooling limit

Set the outside temperature (0..50 °C) above which cooling mode is enabled.
Cooling mode is locked below the set temperature.

Main menu > Apartment > Settings > OT cooling limit:

Factory setting

--- (Inactive – no heating limit)

Setting

………………°C

«
...
29
30
31
32
33
...
»

Summary of Contents for Synco living





































































































Reviews:

No comments

Related manuals for Synco living

Brand: Dantherm Pages: 96

Brand: Jands Pages: 7

coviva Smartbox TKP100A

Brand: hager Pages: 34

Brand: Jabra Pages: 8

Brand: National Instruments Pages: 31

Brand: National Instruments Pages: 24

Brand: National Instruments Pages: 85

Brand: National Instruments Pages: 10

Brand: National Instruments Pages: 16

Brand: National Instruments Pages: 98

CompactRIO cRIO-9002

Brand: National Instruments Pages: 21

Brand: National Instruments Pages: 145

Brand: National Instruments Pages: 42

Brand: National Instruments Pages: 8

Brand: National Instruments Pages: 54

Brand: Parkside Pages: 65

Brand: D+H Pages: 32

Liberty Vertical Picket

Brand: National ramp Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands