manualshive.com logo in svg

Siemens ST950, User Manual

Share
Download
Siemens ST950 User Manual Download Page 74

 

ST950 Plus+ User Manual 

 

  

 

 

ST950 Plus+ User Manual 

Page 74 of 176 

667/HE/53000/000   

Issue 2 

Unrestricted 

 

 

 

Plus

+

 Signal Head 

The Plus

+

 signal head consists of a number of Plus

+

 Aspects (each containing a Plus

+

 LED plate), a 

ByPass  module  and  RAG  Node  all  housed  within  a  standard  Helios  housing.  The  RAG  Node  is 
mounted behind the Green aspect door. 

Instructions for mounting, replacing Helios signal heads and mounting items such as the Solar Cell 
can be found in the Helios Handbook 667/HB/30000/000. 

 

 

Side Mounted Boxes

 

If there is a need for side or inline mounted boxes, the mounting is as standard, however the 

aspect for a Green Arrow will be connected to the GREEN2 connector (see section 4.2.3). 
If there is a need for a further side mounted box (e.g. second Green Arrow optic), an additional 

RAG Node will be allocated and will be mounted within the second Green Arrow box. 

 

4.2.1

 

RAG Node : Overview 

The RAG Node is the interface between the CIC (power / communications distribution) and the 
Plus

+ 

LED aspect. 

The  Plus

+

  LED  plate  contains  pre-programmed  asset  data  which,  when  interrogated  by  the 

associated Node, provides information about the colour of the LEDs on the plate. The Node then 
has a number of checks to ensure the correct aspect colours are connected to the correct output 
connectors. The Plus

+ 

RAG node is able to confirm operation of the Plus

+ 

LED aspect and will send 

appropriate diagnostic information about that as well as about itself back through the CIC to the 
controller. 

 

Summary of Contents for ST950



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands