Siemens ST950 User Manual Download Page 75

Page: 75 / 178

ST950 Plus+ User Manual

Page 75 of 176

667/HE/53000/000

Issue 2

Unrestricted

Figure 38 : Bypass Module and RAG Node

4.2.2

RAG Node Interfaces: Power and Comms (PL4)

The main physical interface to the RAG node is via the Bypass to Node ribbon cable. This cable can
only be connected one way.

Assuming an operational system, once the Bypass cable is pushed into place, the Node will be
provided with power and data.

Assuming correct configuration at the controller, the Node may begin operation immediately.

4.2.3

RAG Node Interfaces: LED signals

SK1

–

4 are used for the LED signal interfaces. For basic RAG installations;

•

RED is connected to SK4

•

Amber is connected to SK3

•

Green is connected to SK2 (also referred to as Green1)

If there is a requirement for a second filter (Second Green);

•

Extra Green must be connected to SK1 (also referred to as Green2).

Bypass Module

Bypass to Node
cable

RAG

Node

Connectors

Digital I/O for On
Street Peripherals

RAG Node Status
LEDs

Connector

for

Regulatory Signs

Spur connector

Summary of Contents for ST950



















































































































































































Search results

Summary of Contents for ST950

Reviews:

Brands by name

Popular brands

Siemens ST950, User Manual

Search results

Summary of Contents for ST950

Reviews:

Brands by name

Popular brands