manualshive.com logo in svg

Siemens ST950, User Manual

Share
Download
Siemens ST950 User Manual Download Page 29

 

ST950 Plus+ User Manual 

 

  

 

ST950 Plus+ User Manual 

Page 29 of 176 

667/HE/53000/000   

Issue 2 

Unrestricted 

 

 

The Controller Rack 

Figure 13, below, shows the ST950 Plus

+

 controller in a 6U 19" rack. 

The 19” Controller Rack is 

sub-divided into one 6U-high bay and two 3U-high bays. The 6U bay is fitted with the CPU Card. 

The arrangement of the rear panel and the rack allows for a number of I/O card or detector options 
to be provided: 

•

 

24in 16out rear-panel mounted I/O module - 667/1/46085/001 

•

 

24in 4out rear-panel mounted I/O module - 667/1/46085/002 

•

 

Intelligent Detector Backplane - 667/1/32910/950 

•

 

ST950 CPU I/O kit 24in 4out - 667/1/46014/000 

•

 

WiMag Standard Interface kit - 667/1/47210/100 

 

Where standard loop detectors are required to be installed in the cabinet, the two 3U-high bays 
can be fitted with up to two Intelligent Detector Backplanes and the middle 6U section can be 
converted to mount a further two IDBs, thereby supporting a total of 16 Loop Detector cards

4

 

(each IDB supports up to 4 Loop Detector cards and each Loop Detector card supports up to 4 
loops). 

If required, a Stratos Outstation unit may be fitted in the bottom right bay, as shown in Figure 13. 

 

The 6U card is held in the rack by a retaining strip at its upper front edge. To release the card, 
loosen the clamping screws and move the retaining strip clear of the card guide. 

 

 

Figure 13 

–

 ST950 Plus

+

 

19” Rack 

- Front

 

 

 

 

4

 Depending on loading. Reference section 3.14 for details. 

4  x  SLD4's  / 
Stratos 
Outstation 

Retaining  

Strip 

CPU Card 

Location 

for 

First  IDB  /  4  x 
SLD4 

Summary of Contents for ST950



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands