Siemens Siwarex U Device Manual Download

Page: 47 / 89

4BWEIGHING FUNCTIONS

5.8.5

DR 31/32 – operating errors

In the 16 bits the pending operating errors are displayed.

Bit no.

Name

Remarks

1= limit for load cell signal exceeded or undershot

See message list Chapter

7.8

1= minimum voltage at the sense line undershot

See message list Chapter

7.8

watchdog

See message list Chapter

7.8

1= error in EPROM

See message list Chapter

7.8

1= error in EEPROM

See message list Chapter

7.8

1= error in RAM

See message list Chapter

7.8

1= ADC error

See message list Chapter

7.8

1= number overflow in weight calculation

See message list Chapter

7.8

1= No 24 V supply

See message list Chapter

7.8

Reserve

Table 5-8

Operating errors

5.8.6

DR 31/32 – data and command errors

In the 16 bits, the data or command errors which occurred most recently are
displayed. The display is reset at the next command or next data transfer.

Bit no.

Name

Remarks

1= adjustment command could not be executed as distance
between adjustment points is too small

See message list Chapter

7.7

1= instruction could not be executed due to fault

See message list Chapter

7.7

1= a non-existent or inactive channel was addressed

See message list Chapter

7.7

1= code not defined (e.g. cutoff frequency, digital filter etc.)

See message list Chapter

7.7

1= data record/command unknown

See message list Chapter

7.7

1= command not possible because scale is not adjusted

See message list Chapter

7.7

1= waiting time of 5 sec. for adjustment commands not
observed

See message list Chapter

7.7

1= the adjustment weight is negative

See message list Chapter

7.7

9 Reserve

Table 5-9

Data or command errors

5.9 DR 40 module info

No entries can be made in DR40. The purpose of the data record is to provide
information about the module version.

Name

Model

Length

Default

Range of Values / Meaning / Display

FW version

WORD

Firmware version

FW checksum

WORD

0…..65535

Reserve

BYTE

Reserve

Number of channels

BYTE

1/2

Number of channels

Model

BYTE

1/0

0= 7MH4601...., 1= 7MH4950.....

Reserve

BYTE

Reserve

Table 5-10

Allocation of DR 40

SIWAREX U

5-39

Summary of Contents for Siwarex U


























































































Search results

Summary of Contents for Siwarex U

Reviews:

Related manuals for Siwarex U

Brands by name

Popular brands

Siemens Siwarex U, Device Manual

Search results

Summary of Contents for Siwarex U

Reviews:

Related manuals for Siwarex U

Brands by name

Popular brands