Siemens sitrans tr300 Manual Download

Page: 20 / 96

SITRANS TR200/TR300
Operating Instructions, 06/2010, A5E01071992-03

Installation

The transmitter is secured to a 35 mm DIN rail to DIN EN 60715.
Comply with the ambient conditions specified in the technical data.

WARNING

Hazardous areas



Gas hazardous area:
– The enclosure has IP20 degree of protection. With an intrinsically-safe power supply,

you can therefore assemble the intrinsically-safe device versions without an

additional enclosure.

– For ic and nA modes, use a suitable protective enclosure / terminal box which

satisfies at least IP54 degree of protection.



Dust hazardous zone:

For use in a dust hazardous zone, install in a suitable metal protective enclosure /

terminal box which satisfies at least IP6X degree of protection.

CAUTION

Electromagnetic Compatibility
If the sensor is installed outside a closed building, you must check the transmitter for

correct functioning following a lightning stroke.

Summary of Contents for sitrans tr300

































































































Search results

Summary of Contents for sitrans tr300

Reviews:

Related manuals for sitrans tr300

Brands by name

Popular brands

Siemens sitrans tr300, Manual

Search results

Summary of Contents for sitrans tr300

Reviews:

Related manuals for sitrans tr300

Brands by name

Popular brands