Siemens SITRANS T4200 Operating Instructions Manual Download

Page: 12 / 100

General safety notes

2.5 Precautions

SITRANS TH200/TH300
Operating Instructions, 06/2010, A5E00393069-03

2.5

Precautions

In the interests of safety, the following precautions must be observed:

WARNING

"Intrinsic safety" type of protection
Connect the device only to certified, intrinsically safe circuits. These circuits must comply

with the technical data specified on the nameplate or in the certificates and approvals.

Should these circuits not match the details given in the certificates and approvals, then the

safety required for the approval can no longer be guaranteed. The device's protection level

"ia" is lowered to protection level "ib" if fail-safe circuits are connected with protection level

"ib".

"Limited energy" type of protection ic/nL (Zone 2)
Devices of the protection type "limited energy" can be connected and disconnected during

operation.

"Non-sparking" type of protection nA (Zone 2)
Devices of the protection type "non-sparking" may only be connected and disconnected

when in a powered-down state.

CAUTION

Modules susceptible to electrical discharge
The device contains modules susceptible to electrical discharge. Modules susceptible to

electrical discharge can be destroyed by voltages that fall far below the limits of human

perception. These voltages even occur if you touch a component part or electrical

connections of a module without being electrostatically discharged. The damage to a

module caused by overvoltage cannot normally be detected immediately, it only becomes

apparent after a longer period of operating time has elapsed.

Summary of Contents for SITRANS T4200





































































































Search results

Summary of Contents for SITRANS T4200

Reviews:

Related manuals for SITRANS T4200

Brands by name

Popular brands

Siemens SITRANS T4200, Operating Instructions Manual

Search results

Summary of Contents for SITRANS T4200

Reviews:

Related manuals for SITRANS T4200

Brands by name

Popular brands