Siemens SITOP PSU8200 Manual Download Page 14

Page: 14 / 66

Description, device design, dimension drawing

2.4 Status displays and signaling

SITOP PSU8200 1ph

Manual, 11.2014, C98130-A7633-A1-3-7629

2.4

Status displays and signaling

6EP3333-8SB00-0AY0 (24 V/5 A)
6EP3334-8SB00-0AY0 (24 V/10 A)

Operating display

④

LED green for "24 V O.K."
Yellow LED for overload in "constant current" mode
Red LED for latching shutdown in "shut down" mode

Signaling contacts (13, 14)

⑤

Relay contact (NO contact, contact rating 30 V AC / 0.5 A, 60 V DC / 0.3 A,

30 V DC / 1 A) for "24 V O.K.".

Figure 2-6

Operating display and signaling contact for 6EP3333-8SB00-0AY0 and

6EP3334-8SB00-0AY0

Signaling

6EP3333-8SB00-0AY0 (24 V/5 A)
6EP3334-8SB00-0AY0 (24 V/10 A)

Green LED lit
Signaling contact, contacts 13-14 closed

Normal operation, output voltage >20 V ±0.5 V

LED off
Signaling contact, contacts 13-14 open

(quiescent position)

No supply voltage

Yellow LED lit
Signaling contact, contacts 13-14 open

(quiescent position)

Overload, output voltage <20 V ±0.5 V (only in "constant current" mode)

Red LED lit
Signaling contact, contacts 13-14 open

(quiescent position)

Latching shut down or remote OFF

Summary of Contents for SITOP PSU8200



































































Search results

Summary of Contents for SITOP PSU8200

Reviews:

Related manuals for SITOP PSU8200

Brands by name

Popular brands

Siemens SITOP PSU8200, Manual

Search results

Summary of Contents for SITOP PSU8200

Reviews:

Related manuals for SITOP PSU8200

Brands by name

Popular brands