Siemens SITOP PSU3800 12 V/20 A User Manual Download Page 11

Page: 11 / 108

SITOP PSU8200/3800 3ph
Manual, 05.2018, C98130-A7638-A1-6-7629

Description, device design, dimension drawing

2.1

Device description

SITOP PSU8200/3800 3ph is a primary-clocked power supply for connection to a 3-phase

AC line supply. An electronically regulated DC voltage that can be set via a potentiometer is

available at the output of the device. The output of the device is isolated, no-load proof and

short-circuit proof. The LED displays indicate the operating state. The operating state of the

device can be processed via the signaling contact. Remote control and remote reset are

possible via the remote ON/OFF.

①

AC input

②

DC output

③

Potentiometer (output voltage)

④

Signaling contact, remote (not for 6EP1437-3BA10)

⑤

Indicator lights (OUTPUT O.K., OVERLOAD, SHUTDOWN)

⑥

Selector switch (ON - OFF)

⑦

DIN rail slider

⑧

Convection

⑨

Clearance above/below

Figure 2-1

Design

Summary of Contents for SITOP PSU3800 12 V/20 A













































































































Search results

Summary of Contents for SITOP PSU3800 12 V/20 A

Reviews:

Related manuals for SITOP PSU3800 12 V/20 A

Brands by name

Popular brands

Siemens SITOP PSU3800 12 V/20 A, User Manual

Search results

Summary of Contents for SITOP PSU3800 12 V/20 A

Reviews:

Related manuals for SITOP PSU3800 12 V/20 A

Brands by name

Popular brands