manualshive.com logo in svg

Siemens SIRIUS 3RW44, Manual

The Siemens SIRIUS 3RW44 is a top-of-the-line motor soft starter. This high-performance device ensures a smooth and reliable start, preventing any potential motor damage. Unlock the full potential of your device by downloading the comprehensive user manual for free from manualshive.com. Get instant access to essential insights and operating instructions to make the most out of your Siemens SIRIUS 3RW44 unit.

Share
Download
background image

 

Installation, connection and feeder configuration 

 

4.2 Design of the feeder 

3RW44 soft starters 
Manual, 03/2017, NEB535219502000/RS-AB/008 

33

 

Contact element 

The 3RW44 soft starter performs the functions of the contact element and motor protection. 

 

 

DANGER 

Hazardous voltage.  

Danger to life or risk of serious injury.  
If line voltage is present at the input terminals of the soft starter, hazardous voltage may still 

be present at the soft starter output even if a start command has not been issued. This 

voltage must be isolated by means of a disconnector (open isolating distance, e.g. with an 

open switch disconnector) whenever work is carried out on the feeder. 

 

4.2.2

 

Soft starters in standard circuits 

The SIRIUS 3RW44 soft starter is connected into the motor feeder between the disconnector 

or motor starter protector and the motor. 
The 3RW44 soft starter automatically detects the type of connection of the soft starter, 

meaning that this does not have to be explicitly set on the device. The detected connection 

type can be read on the starter in the "Status display/Type of connection" menu item. In this 

case, the display reads "Star/delta". If the circuitry is faulty or the motor is not connected, the 

display shows "Unknown". 

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Reviews:

No comments

Related manuals for SIRIUS 3RW44

CAME G5000 Installation, Operation And Maintenance Manual preview
G5000
Brand: CAME Pages: 32
Danfoss VLT MCD 200 Installation Manual preview
VLT MCD 200
Brand: Danfoss Pages: 32
Danfoss PVG 16 PVH/Covers Technical Information preview
PVG 16 PVH/Covers
Brand: Danfoss Pages: 112
Danfoss PVG 100 Service And Parts Manual preview
PVG 100
Brand: Danfoss Pages: 44
Danfoss PVG 16 PVH/Covers Service And Parts Manual preview
PVG 16 PVH/Covers
Brand: Danfoss Pages: 144
Danfoss VLT LCP 11 Installation Instructions preview
VLT LCP 11
Brand: Danfoss Pages: 2
Danfoss VLT FC Series Operating Instructions Manual preview
VLT FC Series
Brand: Danfoss Pages: 64
Danfoss EKC 102A Instructions Manual preview
EKC 102A
Brand: Danfoss Pages: 8
Danfoss VLT AutomationDrive FC 360 Programming Manual preview
VLT AutomationDrive FC 360
Brand: Danfoss Pages: 60
Danfoss DHP-A Installation Instruction preview
DHP-A
Brand: Danfoss Pages: 6
Danfoss AMV 110 NL AQT Datasheet preview
AMV 110 NL AQT
Brand: Danfoss Pages: 4
Danfoss VLT FC Series Installation Manual preview
VLT FC Series
Brand: Danfoss Pages: 8
Danfoss AK-CC 550A Troubleshooting Manuallines preview
AK-CC 550A
Brand: Danfoss Pages: 2
Danfoss ECL Comfort 110 Quick Manual preview
ECL Comfort 110
Brand: Danfoss Pages: 2
Danfoss 103E5 Installation & User'S Instructions preview
103E5
Brand: Danfoss Pages: 24
Hach SC4200c User Manual preview
SC4200c
Brand: Hach Pages: 36
Hach 2100Q User Instructions preview
2100Q
Brand: Hach Pages: 72
Harmonic Drive CHA Engineering Data preview
CHA
Brand: Harmonic Drive Pages: 85

Brands by name

Popular brands

Load more brands