manualshive.com logo in svg

Siemens SIRIUS 3RW44, Manual

The Siemens SIRIUS 3RW44 is a top-of-the-line motor soft starter. This high-performance device ensures a smooth and reliable start, preventing any potential motor damage. Unlock the full potential of your device by downloading the comprehensive user manual for free from manualshive.com. Get instant access to essential insights and operating instructions to make the most out of your Siemens SIRIUS 3RW44 unit.

Share
Download
background image

 

 

3RW44 soft starters 

20

 

Manual, 03/2017, NEB535219502000/RS-AB/008 

 

Configuration instructions 

3 

3.1

 

Configuration 

The 3RW44 electronic soft starters are designed for normal starting. In case of heavy 

starting or increased starting frequency, a larger unit may have to be selected. 
For long starting times it is recommended to have a PTC sensor in the motor. This also 

applies to soft stop, pump stop and DC braking coasting methods because, during the coast-

down time in these modes, an additional current loading applies in contrast to coasting 

down. 
The motor feeder between the soft starter and motor must not contain any capacitive 

elements (such as compensation systems). Active filters must not be operated in 

combination with soft starters. 
All elements of the main circuit (such as fuses and switching devices) should be 

dimensioned for direct-on-line starting, following the local short-circuit conditions, and must 

be ordered separately. 
The harmonic component load for starting currents must be taken into consideration for the 

selection of motor starter protectors (selection of trip unit). 
 

3.1.1

 

RS 232 serial PC interface and Soft Starter ES parameterizing and operating 

software 

The electronic 3RW44 soft starters have a PC interface for communicating with the Soft 

Starter ES smart software and an operating and monitoring module (display). 

3.1.2

 

Simulation Tool for Soft Starters (STS) 

With this software, you can simulate and select all Siemens soft starters, taking into account 

various parameters such as line conditions, motor and load data, and special application 

requirements, etc. 
The Simulation Tool for Soft Starters (STS) can be downloaded from the Internet 

(

https://support.industry.siemens.com/cs/ww/en/view/101494917

). 

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Reviews:

No comments

Related manuals for SIRIUS 3RW44

3Ware 7000-2 - Escalade RAID Controller Features preview
7000-2 - Escalade RAID Controller
Brand: 3Ware Pages: 2
BADLANDS LE-03 Quick Manual preview
LE-03
Brand: BADLANDS Pages: 2
halstrup-walcher PSD4 Series Instruction Manual preview
PSD4 Series
Brand: halstrup-walcher Pages: 39
Parker ACR7000 Series Hardware Manual preview
ACR7000 Series
Brand: Parker Pages: 21
Parker AC890PX Series Quick Start Manual preview
AC890PX Series
Brand: Parker Pages: 26
Parallax 700-10016 Manual preview
700-10016
Brand: Parallax Pages: 3
S&P RMB Series Manual preview
RMB Series
Brand: S&P Pages: 12
S&C Vista SD Programming preview
Vista SD
Brand: S&C Pages: 34
S&C Micro-AT Operation preview
Micro-AT
Brand: S&C Pages: 32
S&C IntelliCap Plus Installation Manual preview
IntelliCap Plus
Brand: S&C Pages: 32
S&P REB 5 Manual preview
REB 5
Brand: S&P Pages: 12
S&C PMH Instructions For Operation Manual preview
PMH
Brand: S&C Pages: 35
Parker SciLog DINCon Installation, Operating, & Maintenance Instructions preview
SciLog DINCon
Brand: Parker Pages: 42
DSE DSE 6120 Installation Instructions preview
DSE 6120
Brand: DSE Pages: 2
Baier 50VA Instruction Manual preview
50VA
Brand: Baier Pages: 20
K&K M4700B Installation Instructions Manual preview
M4700B
Brand: K&K Pages: 10
Idemia MorphoAccess VP MD Quick User Manual preview
MorphoAccess VP MD
Brand: Idemia Pages: 29
Sonos Controller CR100 Brochure & Specs preview
Controller CR100
Brand: Sonos Pages: 2

Brands by name

Popular brands

Load more brands