Siemens SIRIUS 3RW44 Manual Download Page 141

Page: 141 / 292

Diagnostics and messages

8.1 Diagnostics and messages

3RW44 soft starters
Manual, 03/2017, NEB535219502000/RS-AB/008

141

8.1.2

Warnings and group faults

①

Warning

②

Fault without restart

③

Fault with restart

Message

①

②

③

Cause/solution

No supply voltage

Start command has been issued although the main voltage is not

yet applied.
Remedy: Switch on the supply voltage.

If the message occurs in the bypass mode, it may have been

generated erroneously by a too frequently generated "Prewarning

limit - motor heating", "Remaining time for tripping" or "I

limit

exceeded/undershot" warning (can also be traced via the entries in

the logbook/events).
Remedy: See description of applicable messages

Main voltage is removed simultaneously with the ON command,

although run down (not "Coasting down") is parameterized.
Remedy: Activate line contactor by means of output parameterized

to ON time or parameterize "Coasting down".

Incorrect starting conditions

(for devices with product version

< *E04*)
Phase angle control faults

(for devices with product version

≥

*E04*)

Fault occurs without motor starting.
Cause:
–

Motor has not been connected correctly.

–

Inside-delta circuit is wrongly configured.

–

There is a ground fault.

Remedy: Check and correct wiring (see circuit suggestions for

inside-delta circuit).

Fault occurs during starting.
Cause:
–

Chosen starting voltage too high

–

Breakaway pulse (wrongly) set: Motor starting becomes

unstable

(set the breakaway pulse only when it is really required. In the case

of pumps, for example, a breakaway pulse often leads to misfiring.)

If there is an idle time < 5 s since the last start, the 3RW44 starts

with a higher starting voltage. In combination with a set breakaway

pulse, this can lead to "incorrect starting conditions".
Remedy: Adjust parameters or extend idle time.

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands

Siemens SIRIUS 3RW44, Manual

Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands