Siemens SINUMERIK ONE NCU 1740 Equipment Manual Download Page 51

Page: 51 / 164

7.3

Fix the NCU using spacers

Introduction

Spacers can be used to mount the NCU on a bare-metal highly-conductive rear panel of a control
cabinet.

Note

The mechanical stability for horizontal mounting is only guaranteed with the help of supports
or similar. These must be clarified depending on the specific application and are not part of this
documentation.

Procedure

Mount the NCU using two M6 screws (6 Nm tightening torque) on the spacers on the rear of the
control cabinet.

7.4

Mounting the NCU without spacers

Procedure

The NCU has spacers on the upper and lower rear side, each fixed with three Torx M3 screws as
delivered.

1. Remove the spacers with a T10 screwdriver.

2. At the top and bottom, fasten the metal lugs of the NCU directly to the rear panel of the

control cabinet using two M6 screws (6 Nm).

Installation

7.4 Mounting the NCU without spacers

NCU 1740
Equipment Manual, 10/2021, A5E51087503B AA

Summary of Contents for SINUMERIK ONE NCU 1740





































































































































































Search results

Summary of Contents for SINUMERIK ONE NCU 1740

Reviews:

Related manuals for SINUMERIK ONE NCU 1740

Brands by name

Popular brands

Siemens SINUMERIK ONE NCU 1740, Equipment Manual

Search results

Summary of Contents for SINUMERIK ONE NCU 1740

Reviews:

Related manuals for SINUMERIK ONE NCU 1740

Brands by name

Popular brands