Siemens SIMOTION P320-4 E Commissioning And Hardware Installation Manual Download Page 79

Page: 79 / 222

Mounting

5.1

Installation overview

The SIMOTION P320‑4 is installed in a cabinet or in a controller housing.

Unlocking Windows

Note
Windows locked
Windows may be accidentally locked, e.g. through shortcut key Ctrl+L. If you do not know the

password for the SIMOTION P320-4, please contact the Siemens Industry Online Support

(

https://support.industry.siemens.com/cs/ww/en/

Operating mode

Two operating modes are available for the installation of a SIMOTION P320‑4:
● SIMOTION P320-4 - Headless operation (Page 79)
● Distributed configuration of the SIMOTION P320‑4 with a remote panel (Page 82)

5.2

Headless operation

5.2.1

SIMOTION P320-4 - Headless operation

The SIMOTION P320-4 is operated without a screen, e.g. SIMATIC panel, SIMOTION P320-4

is installed in a cabinet.
The maintenance and configuration is performed via a computer that accesses the SIMOTION

P320-4 by means of remote desktop.

SIMOTION P320-4 E / P320-4 S

Commissioning and Hardware Installation Manual, 11/2016

Summary of Contents for SIMOTION P320-4 E































































































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Commissioning And Hardware Installation Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands