manualshive.com logo in svg

Siemens SIMOTION P320-4 E, Commissioning And Hardware Installation Manual

The Siemens SIMOTION P320-4 E is a cutting-edge automation system with advanced features. Ensure a seamless setup and smooth operation by utilizing the comprehensive "Commissioning And Hardware Installation Manual". Download this valuable manual for free at our website, manualshive.com, to unlock the full potential of your Siemens SIMOTION P320-4 E.

Share
Download
background image

10.11

Switching off

Windows

To ensure the safe operation of the SIMOTION P320-4, Windows must be properly shut down 

before the SIMOTION P320-4 is switched off.

Note
Use the Windows start menu to correctly shut down the Windows system: Start > Shut down

If Windows is not shut down properly, the Windows installation may become damaged to the 

extent that it may no longer be possible to run the SIMOTION P320-4.

Note
Only applies to the SIMOTION P320-4 E
SIMOTION P320-4 E is delivered with deactivated EWF (Enhanced Write Filter). 
After commissioning the SIMOTION P320-4 E, activate the EWF for drive C:, which ensures:
● An extended service life for the internal CFast card
● No data loss on the internal CFast card when switching the device off via the line side switch 

or through disconnection from the power supply

NOTICE
Do not protect external CFast cards with EWF
Drive D: - the external CFast card - must not be protected with EWF as otherwise the 

functionality of SIMOTION cannot be assured.

NOTICE
Threat of data loss
Always shut down SIMOTION correctly as otherwise there is a threat of data loss.

SIMOTION P320-4

If Windows is shut down properly, the SIMOTION P320-4 will also be shut down properly. 
If the SIMOTION P320-4 is switched off before Windows is shut down correctly, the POWER 

FAIL functionality causes the following events to occur. 
● SIMOTION P320-4 is stopped correctly
● The SIMOTION P retain variables are saved in the non-volatile memory of the 

SIMOTION P320‑4.

When SIMOTION P320-4 powers up again, the backed-up user data will be available once 

more. 

Commissioning (software)
10.11 Switching off

SIMOTION P320-4 E / P320-4 S

178

Commissioning and Hardware Installation Manual, 11/2016

Summary of Contents for SIMOTION P320-4 E































































































































































































































Reviews:

No comments

Related manuals for SIMOTION P320-4 E

Bihong Q-JET Operation Manual preview
Q-JET
Brand: Bihong Pages: 37
ASAHI BMK1800 Installation And Maintenance Instruction preview
BMK1800
Brand: ASAHI Pages: 9
Kärcher HDC 40/16 Manual preview
HDC 40/16
Brand: Kärcher Pages: 396
Valor 18385 Owner'S Manual preview
18385
Brand: Valor Pages: 65
iceqube IQ700HE Operation And Installation Manual preview
IQ700HE
Brand: iceqube Pages: 29
B&R Power Panel T30 User Manual preview
Power Panel T30
Brand: B&R Pages: 140
Tsubaki MGUS Series Installation And Maintenance Instruction preview
MGUS Series
Brand: Tsubaki Pages: 3
ALEGRE HYBRID BOX Instructions For Use & Maintenance preview
HYBRID BOX
Brand: ALEGRE Pages: 19
Baileigh BB-4816M-V2 Operator'S Manual preview
BB-4816M-V2
Brand: Baileigh Pages: 36
Covaris E220-plus Setup & Instruction Manual preview
E220-plus
Brand: Covaris Pages: 59
PCB 1408-02ADB Installation And Operating Manual preview
1408-02ADB
Brand: PCB Pages: 16
D&R ELECTRONICS Ford F-150 K9 Kennel Instruction Manual preview
Ford F-150 K9 Kennel
Brand: D&R ELECTRONICS Pages: 10
Murata GQM22M5C2H620JB01 Series Reference Sheet preview
GQM22M5C2H620JB01 Series
Brand: Murata Pages: 25
ITOH DENKI PM605KT Technical Documentation Manual preview
PM605KT
Brand: ITOH DENKI Pages: 39
Jäger Z42-M160.20 S5 Manual preview
Z42-M160.20 S5
Brand: Jäger Pages: 36
IBASE Technology UPC-7210 Series User Manual preview
UPC-7210 Series
Brand: IBASE Technology Pages: 77
Kval DL-NCD Operation Manual preview
DL-NCD
Brand: Kval Pages: 144
DOYMA Curaflex Nova Uno/M/Z Installation Instructions preview
Curaflex Nova Uno/M/Z
Brand: DOYMA Pages: 4

Brands by name

Popular brands

Load more brands